ITEM DESCRIPTION FOR PR: 0045033122

  STOCK,GUN,SHOULDER
  THIS ITEM IS A "DEFENSE ARTICLE" AS DEFINED IN AND
  SUBJECT TO THE
  INTERNATIONAL TRAFFIC IN ARMS REGULATIONS (22
  C.F.R. 120-30) AND THE
  ARMS EXPORT CONTROL ACT (22 U.S.C.A. 2778-2799).
  ANY MANUFACTURER OR
  EXPORTER OF DEFENSE ARTICLES IS REQUIRED TO
  REGISTER WITH THE
  DIRECTORATE OF DEFENSE TRADE CONTROLS (DDTC),
  DEPARTMENT OF STATE.
  DOCUMENTARY EVIDENCE OF REGISTRATION MAY BE
  REQUIRED PRIOR TO AWARD.
  ADDITIONAL EXPORT RESTRICTIONS APPLY AS INDICATED
  HEREIN. FAILURE TO
  SUBMIT DDTC REGISTRATION WHEN REQUESTED WILL MAKE
  A QUOTE/OFFER
  INELIGIBLE FOR AWARD.
  _______________EXCEPTION DATA____________________
  MIL-DTL-16232, para 6.2.1- DD FORM 1423 is
  replaced by SUPPLEMENTAL QUALITY ASSURANCE
  PROVISION (SQAP) PHOS-DL-MANG
  IF DRAWING NOTE GIVES OPTION FOR ZINC OR
  MANGANESE COATING THEN MANGANESE IS REQUIRED.
  13023911: Delete ASTM D4080 and replace with "Any
  method of vapor degreasing or solvent cleaning
  that
  leaves a clean and water break free surface, and
  removes any organic contaminants or other
  interfering
  films is acceptable.#
  TDPL:
  Document Delete Substitute Add
  SAE AMS13572 X - -
  ______________END OF EXCEPTIONS__________________
  __________SPECIAL PACKAGING INSTRUCTIONS_________
  SPECIFICATIONS, STANDARDS AND DRAWINGS LISTED
  HEREON
  OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR
  BID
  FORM A PART OF THIS PACKAGING INSTRUCTION. THE
  APPLICABLE GENERAL AND REFERENCED REQUIREMENTS OF
  SPECIFICATION MIL-STD-2073-1 FORM PART OF THESE
  INSTRUCTIONS. UNLESS OTHERWISE SPECIFIED,
  MATERIALS
  WILL BE MINIMUM SIZE IN ACCORDANCE WITH
  MIL-STD-2073-1. WEIGHTS AND SIZES ARE ESTIMATED
  AND
  MAY VARY SLIGHTLY. INTERMEDIATE PACKAGING AND
  PACKING
  WILL BE IN ACCORDANCE WITH SPECIFICATION
  MIL-STD-2073-1 OR AS OTHERWISE SPECIFIED HEREIN.
  TOLERANCES SHALL BE IN ACCORDANCE WITH MATERIAL
  SPECIFICATIONS. QUALITY PERFORMANCE AND TESTING
  REQUIREMENTS SHALL BE IN CONFORMANCE WITH
  MIL-STD-2073-1, OR AS OTHERWISE SPECIFIED.
  * UNLESS OTHERWISE SPECIFIED, CLEANING AND DRYING
  SHALL BE IN ACCORDANCE WITH PARAGRAPH 5.2.1 OF
  MIL-STD-2073-1.
  A. BAG SHALL BE NON-TOXIC, TRANSPARENT, 4 MIL
  THICK
  POLYETHYLENE FILM HAVING A MULTI-METAL VOLATILE
  CORROSION INHIBITOR. BAG SHALL BE FABRICATED IN
  ACCORDANCE WITH MIL-DTL-117 FOR A CLASS-B BAG.
  SUGGESTED SOURCES OF SUPPLY:
  MANUFACTURER PRODUCT
  CORTEC VpCI 126
  DAUBERT-CROMWELL PREMIUM METAL GUARD
  ZERUST ICT 510-C MULTI-METAL
  B. COMPATIBILITY PROVISIONS OF MIL-I-8574 APPLY.
  ______END OF SPECIAL PACKAGING INSTRUCTIONS______
  THE ITEM BEING PROCURED IS A CRITICAL GUN PART
  ITEM WITH UNIQUE REQUIREMENTS.
  IF REQUIRED BY CONTRACT, CONTRACTOR FIRST ARTICLE
  TEST APPLIES.
  PROCESS PROCEDURES AND OR WORKMANSHIP SPECIMENS
  REQUIRED BY MILITARY SPECIFICATION (S) APPLICABLE
  TO THIS CONTRACT WILL BE APPROVED BY THE CONTRACT
  POST AWARD CONTRACTING OFFICER (PCO). POST AWARD
  PREPRODUCTION APPROVAL VERIFYING THE REQUIREMENTS
  OF MIL-DTL-16232 IS REQUIRED.
  A CONTRACT DATA REQUIREMENTS LIST (CDRL),
  IDENTIFIED IN A SQAP AS A PHOS-DL-MANG AND A
  SUGGESTED OUTLINE, IDENTIFIED IN A SQAP AS PHOS-
  OUTLINE-16232, PROVIDE THE PHOSPHATE COATING
  PROCEDURE REQUIREMENTS/FORMAT AND ARE INCLUDED IN
  THE TECHNICAL DATA PACKAGE.
  THE CONTRACTOR MUST PROVIDE COPIES OF PHOSPHATE
  COATING PROCEDURES WRITTEN SPECIFICALLY FOR THE
  COATING OF PARTS ON THIS CONTRACT TO THE PCO
  WITHIN 45 DAY AFTER AWARD. AN ADDITIONAL 30 DAYS
  WILL BE REQUIRED FOR REVIEW/APPROVAL
  DETERMINATION.
  PRODUCT INSPECTION WILL BE CONDUCTED BY THE DCMA
  QAR AT THE ACTUAL MANUFACTURER'S FACILITY AND IN
  PROCESS INSPECTIONS WILL OCCUR AT THE PHOSPHATE
  CONTRACTOR'S FACILITY IDENTIFIED ON THIS
  CONTRACT. THE IDENTIFICATION OF THE ACTUAL
  MANUFACTURER AND PHOSPHATE CONTRACTOR MUST BE
  SUBMITTED TO THE CONTRACTING OFFICER FOR
  INCLUSION IN THE AWARD. UPON AWARD, ANY CHANGES
  TO THE ABOVE MUST BE APPROVED BY THE PCO VIA
  FORMAL CONTRACT MODIFICATION.
  A WAIVER FOR THE PHOSPHATE PREPRODUCTION
  REQUIREMENTS OF MIL-DTL-16232 PARAGRAPH 3.1 CAN
  BE SUBMITTED. THE DOCUMENTATION REQUIRED FOR
  EVALUATION OF THIS WAIVER REQUEST MUST INCLUDE:
  A PHOSPHATE PROCEDURE THAT HAS BEEN REVIEWED AND
  APPROVED BY THIS PROCURING AGENCY AND A TEST
  REPORT (GOVERNMENT FIRST ARTICLE OR PRODUCTION
  VERIFICATION TEST)FROM WITHIN THE LAST YEAR IN
  WHICH THE PHOSPHATE COATING WAS TESTED AND PASSED
  (FOR ANY NSN).
  THIS NSN CONTAINS ONE OR MORE COMPONENTS WHICH
  MUST MEET QPL/QML SPECIFICATIONS AS IDENTIFIED
  IN THE TECHNICAL DATA PACKAGE. CLAUSE I09A01
  (FAR CLAUSE 52.209-1) QUALIFICATION REQUIREMENTS
  IS APPLICABLE. THE AWARDEE SHALL PROVIDE QPL/QML
  COMPONENTS ONLY FROM SOURCES QUALIFIED ON THE
  APPLICABLE QPL(S)/QML(S). THE IDENTIFICATION OF
  ALL APPLICABLE QPL/QML SOURCES MUST BE SUBMITTED
  TO THE CONTRACTING OFFICER FOR EVALUATION PRIOR
  TO CONTRACT AWARD.
  PRODUCT VERIFICATION TESTING (PVT) CLAUSE DLAD
  52.246-9004 MAY BE INVOKED FOR THE REFERENCED
  CONTRACT. IF INVOKED, PVT SAMPLES MUST BE
  INSPECTED, PACKAGED AND MARKED AS REQUIRED IN THE
  CONTRACT. ONE (1) SAMPLE MAY BE DESTROYED DURING
  TESTING.
  PRODUCT VERIFICATION TESTING, IF INVOKED, WILL BE
  PERFORMED PRIOR TO ACCEPTANCE OF EACH SHIPMENT.
  THE CONTRACTOR MUST PROVIDE PVT SAMPLES FROM EACH
  SUBCONTRACTOR AND FROM EACH PHOSPHATE CONTRACTOR
  USED IN THE PRODUCTION OF PARTS ON THIS CONTRACT.
  FIVE (5) PVT SAMPLES WILL BE REQUIRED TO BE
  IDENTIFIED TO THOSE SUBCONTRACTORS AND PHOSPHATE
  CONTRACTORS WHEN THEY ARE SENT IN FOR TESTING.
  CERTIFICATE OF CONFORMANCE IS NOT AUTHORIZED.
 
THE INTERNATIONAL ORGANIZATION FOR
STANDARDIZATION (ISO) 9002 OR A "TAILORED"
PROGRAM MEETING THE FOLLOWING ISO 9002
PARAGRAPHS APPLIES:
4.5, DOCUMENT CONTROL: LIMITED TO INSPECTION
AND TESTING AS WELL AS APPLICABLE DRAWINGS,
SPECIFICATIONS AND INSTRUCTIONS REQUIRED BY
CONTRACT
4.6, PURCHASING: 4.6.1 AND LIMITED TO 4.6.2 A)
AND 4.6.4.2, ALL OTHER PARTS OF PARAGRAPH
ARE HEREBY DELETED
4.7, CUSTOMER-SUPPLIED PRODUCT:
4.8, PRODUCT IDENTIFICATION & TRACEABILITY:
4.10, INSPECTION & TESTING:
4.11, INSPECTION, MEASURING & TEST EQUIPMENT:
4.12, INSPECTION AND TEST STATUS:
4.13, CONTROL OF NONCONFORMING PRODUCT:
4.14, CORRECTIVE AND PREVENTIVE ACTION:
PARAGRAPH 4.14.3 APPLY TO PRODUCT ONLY
4.16, QUALITY RECORDS:
FAR CLAUSE 52.246-11 APPLIES
 
DLAD 52.246-9003, MEASURING AND TEST EQUIPMENT,
APPLIES.
 
CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE
USED NOR INCORPORATED IN ANY ITEMS TO BE
DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION
SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT
DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.
SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR
APPROVAL UNLESS THEY ARE AUTHORIZED BY THE
SPECIFICATION REQUIREMENTS.
 
THIS ITEM HAS TECHNICAL DATA SOME OR ALL OF
WHICH IS SUBJECT TO
EXPORT-CONTROL REGULATIONS. DISTRIBUTION OF THE
TECHNICAL DATA
AND ELIGIBILITY FOR AWARD ARE LIMITED TO THOSE
SUPPLIERS QUALIFIED THROUGH JCP CERTIFICATION,
OR TO THOSE LICENSED BY EITHER THE DEPARTMENTS
OF STATE OR COMMERCE; OR TO FOREIGN SUPPLIERS
PURSUANT TO INTERNATIONAL AGREEMENTS.

TO APPLY FOR JCP CERTIFICATION, COMPLETE DD FORM
2345, "MILITARY
CRITICAL TECHNICAL DATA AGREEMENT," FORM IS
AVAILABLE AT THE WORLD WIDE WEB ADDRESS
HTTP://WWW.DLIS.DLA.MIL/JCP OR BY WRITING TO:

DLA LOGISTICS INFORMATION SERVICE
FEDERAL CENTER
74 WASHINGTON AVE., NORTH
BATILE CREEK, MI 49017-3084

TO MANUFACTURE THIS ITEM, NON-JCP CERTIFIED
SUPPLIERS MUST SUBMIT A CURRENT MANUFACTURING
LICENSE AGREEMENT, TECHNICAL ASSISTANCE
AGREEMENT, DISTRIBUTION AGREEMENT OR OFF-SHORE
PROCUREMENT AGREEMENT APPROVED BY THE
DIRECTORATE OF DEFENSE TRADE CONTROLS WITH THE
OFFER, UNLESS AN EXEMPTION UNDER THE PROVISIONS
OF ITAR SECTION, 125.4 "EXEMPTIONS OF GENERAL
APPLICABILITY," AND/OR EAR PART 740 ARE
APPLICABLE.

NON-JCP CERTIFIED SUPPLIERS SEEKING EXPORT
CONTROLLED TECHNICAL
DATA ARE REQUIRED TO PROVIDE THE CONTRACTING
OFFICER WITH AN
APPLICABLE AGREEMENT OR IDENTIFY WHICH ITAR/EAR
EXEMPTION APPLIES TO RECEIVE A COPY OF THE
EXPORT CONTROLLED TECHNICAL DATA.

NOTE:  JCP CERTIFIED CONTRACTORS WHO RECEIVE
TECHNICAL DATA PURSUANT TO THEIR DD FORM 2345
CERTIFICATION MAY NOT FURTHER DISSEMINATE SUCH
DATA UNLESS FURTHER DISSEMINATION OF THE
TECHNICAL DATA IS EXPRESSLY PERMITTED BY DODD
5230.25."

 
A forging process was identified as a means to
manufacture this item.  Tooling is required to
produce a forging.  For additional information:
http://www.aviation.dla.mil/ExternalWeb/UserWeb/
AviationEngineering/SupplyChainAssistance.asp

CRITICAL APPLICATION ITEM

I/A/W   QAP    16236 PHOS-DL-MANG
REFNO
AMEND NR      DTD 11/05/10
TYPE NUMBER

I/A/W   QAP    16236 PHOS-OUTLINE-16232
REFNO
AMEND NR A     DTD 10/15/10
TYPE NUMBER

I/A/W   QAP    16236 PHOS-QAR-CHECK
REFNO
AMEND NR A     DTD 10/15/10
TYPE NUMBER

I/A/W   DRAWING NR 19200 12012081
REFNO
AMEND NR E     DTD 02/23/10
TYPE NUMBER

I/A/W   DRAWING NR 19200 12012082
REFNO
AMEND NR C     DTD 09/10/11
TYPE NUMBER

I/A/W   DRAWING NR 19200 12012083
REFNO
AMEND NR B     DTD 04/21/11
TYPE NUMBER

I/A/W   DRAWING NR 19200 12579607
REFNO
AMEND NR C     DTD 08/04/09
TYPE NUMBER

I/A/W   DRAWING NR 19200 12993884
REFNO
AMEND NR C     DTD 11/15/10
TYPE NUMBER

I/A/W   DRAWING NR 19200 12993884
REFNO
AMEND NR E     DTD 07/21/11
TYPE NUMBER

I/A/W   DRAWING NR 19200 13023910
BASIC
AMEND NR A     DTD 03/31/11
TYPE NUMBER

I/A/W   DRAWING NR 19200 13023910
REFNO
AMEND NR A     DTD 04/07/09
TYPE NUMBER

I/A/W   DRAWING NR 19200 13023910
REFNO
AMEND NR      DTD 01/30/09
TYPE NUMBER

I/A/W   DRAWING NR 19200 13023910
REFNO
AMEND NR      DTD 03/22/12
TYPE NUMBER

I/A/W   DRAWING NR 19200 13023911
REFNO
AMEND NR      DTD 01/03/09
TYPE NUMBER

I/A/W   DRAWING NR 19200 13023912
REFNO
AMEND NR      DTD 01/30/09
TYPE NUMBER

I/A/W   DRAWING NR 19200 13023913
REFNO
AMEND NR      DTD 01/30/11
TYPE NUMBER

I/A/W   DRAWING NR 19200 13036819
REFNO
AMEND NR A     DTD 09/12/11
TYPE NUMBER

I/A/W   DRAWING NR 19200 13036819
REFNO
AMEND NR      DTD 03/25/11
TYPE NUMBER

I/A/W   DRAWING NR 19200 8448521
REFNO
AMEND NR N     DTD 01/30/09
TYPE NUMBER

I/A/W   DRAWING NR 19200 8448618
REFNO
AMEND NR J     DTD 01/30/09
TYPE NUMBER

I/A/W   DRAWING NR 19200 8448619
REFNO
AMEND NR M     DTD 04/21/11
TYPE NUMBER

I/A/W   DRAWING NR 19200 8448652
REFNO
AMEND NR N     DTD 04/21/11
TYPE NUMBER

I/A/W   DRAWING NR 19200 9349122
REFNO
AMEND NR J     DTD 09/12/11
TYPE NUMBER

I/A/W   DRAWING NR 19200 9390014
REFNO
AMEND NR G     DTD 03/31/11
TYPE NUMBER

I/A/W   DRAWING NR 19200 9390019
REFNO
AMEND NR H     DTD 04/21/11
TYPE NUMBER

I/A/W   DRAWING NR 19200 9390020
REFNO
AMEND NR J     DTD 09/26/05
TYPE NUMBER

I/A/W   DRAWING NR 19200 9390021
REFNO
AMEND NR E     DTD 09/20/10
TYPE NUMBER

I/A/W   DRAWING NR 19200 9390022
REFNO
AMEND NR A     DTD 09/26/02
TYPE NUMBER

I/A/W   DRAWING NR 19200 9390025
REFNO
AMEND NR D     DTD 11/15/11
TYPE NUMBER

I/A/W   DRAWING NR 19200 9390026
REFNO
AMEND NR B     DTD 11/06/01
TYPE NUMBER

I/A/W   DRAWING NR 19200 9390026
REFNO
AMEND NR D     DTD 11/15/11
TYPE NUMBER

I/A/W   DRAWING NR 19200 9390027
REFNO
AMEND NR C     DTD 11/06/01
TYPE NUMBER

I/A/W   DRAWING NR 19200 L10S5117
REFNO
AMEND NR F     DTD 01/31/11
TYPE NUMBER

I/A/W   DRAWING NR 19200 L10S5117-9390014
REFNO
AMEND NR      DTD 01/31/11
TYPE NUMBER

I/A/W   DRAWING NR 19200 L2S3025
REFNO
AMEND NR E     DTD 04/15/02
TYPE NUMBER

I/A/W   DRAWING NR 19204 8448619
REFNO
AMEND NR L     DTD 03/25/11
TYPE NUMBER

I/A/W   SPEC NR MIL-DTL-16232G
REFNO
AMEND NR G
TYPE NUMBER

I/A/W   SPEC NR MIL-PRF-3150E
REFNO
AMEND NR 2
TYPE NUMBER

I/A/W   SPEC NR MIL-PRF-46010G
REFNO
AMEND NR G
TYPE NUMBER