Past Bid Detail | BidFortune

Past Bid Detail Page

Hi,

Federal Bid

Last Updated on 25 Dec 2010 at 9 AM

Solicitation

Location Unknown

ROD ASSEMBLY, DRIVING SPRING

Solicitation ID SPM7L411R0010

Source Signup to get source link

Posted Date 26 Oct 2010 at 12 PM

Archive Date 25 Dec 2010 at 5 AM

NAICS Category

Product Service Code

Set Aside No Set-Aside Used

Contracting Office Dla Land And Maritime

Agency Department Of Defense

Location United states

ITEM DESCRIPTION FOR PR: 0027424606

ROD ASSEMBLY, DRIVING SPRING.
***************** ENGINEERING EXCEPTION DATA
*******************
11826032-Note 2:
-Delete ASTM-B221/A211M and Replace with ASTM
B221M OR ASTM A211M.
Remove ASTM B221/A211M from the TDPL.
DWG. 11826030 - Spring Return. The Verification
Level(VL) shall be IV
for all Major Quality Assurance Provisions(QAPs),
not the III that is
indicated on the drawing.
Remove QS11826024, 11826328, and 11826329 from the
TDP/TDPL.
To all drawings and associated documents without a
distribution
statement, add distribution A.
************* END OF ENGINEERING EXCEPTION DATA
****************
************ SPECIAL MILITARY PACKAGING
INSTRUCTIONS ***********
SPI 11826024:
-ADD DISTRIBUTION CODE A.
-DELETE REQUIREMENTS AND ADD THE FOLLOWING NOTES:
SPECIFICATIONS, STANDARDS AND DRAWINGS LISTED
HEREON OF THE ISSUE IN
EFFECT ON DATE OF INVITATION FOR BID FORM A PART
OF THIS PACKAGING
INSTRUCTION. THE APPLICABLE GENERAL AND REFERENCED
RQUIREMENTS OF
SPECIFICATION MIL-STD-2073-1
FORM PART OF THESE INSTRUCTIONS. UNLESS OTHERWISE
SPECIFIED, MATERIALS
WILL BE MINIMUM SIZE IN ACCORDANCE WITH
MIL-STD-2073-1. WEIGHTS AND
SIZES ARE ESTIMATED AND MAY VARY SLIGHTLY.
TOLERANCES SHALL BE IN ACCORDANCE WITH MATERIAL
SPECIFICATIONS. QUALITY
PERFORMANCE AND TESTING REQUIREMENTS SHALL BE IN
CONFORMANCE WITH
MIL-STD-2073-1, OR AS OTHERWISE SPECIFIED.
* UNLESS OTHERWISE SPECIFIED, CLEANING AND DRYING
SHALL BE IN ACCORDANCE
WITH PARAGRAPH 5.2.1 OF MIL-STD-2073-1.
A. BAG SHALL BE NON-TOXIC, TRANSPARENT, 4 MIL
THICK POLYETHYLENE FILM
HAVING A MULTI-METAL VOLATILE CORROSION INHIBITOR.
BAG SHALL BE
FABRICATED IN ACCORDANCE WITH MIL-DTL-117 FOR A
CLASS-B BAG.
SUGGESTED SOURCES OF SUPPLY:
MANUFACTURER PRODUCT
CORTEC VpCI 126
DAUBERT-CROMWELL PREMIUM METAL-GUARD
ZERUST ICT 510-C MULTI-METAL
B. COMPATIBILITY PROVISIONS OF MIL-I-8574 APPLY.
************ END OF SPECIAL MILITARY PACKQAGING
DATA ***********
IF REQUIRED BY CONTRACT, CONTRACTOR FIRST ARTICLE
TEST APPLIES.
PROCESS PROCEDURES AND OR WORKMANSHIP SPECIMENS
REQUIRED BY MILITARY
SPECIFICATION (S) APPLICABLE TO THIS CONTRACT WILL
BE APPROVED BY THE
CONTRACT POST AWARD CONTRACTING OFFICER (PCO).
POST AWARD PREPRODUCTION
APPROVAL VERIFYING THE REQUIREMENTS OF
MIL-DTL-16232 IS REQUIRED.
A CDRL (FORM 1423) AND A SUGGESTED OUTLINE THAT
DETAILS PHOSPHATE
COATING REQUIREMENTS/FORMAT EXIST FOR THIS
MATERIAL. ADDITIVE CLIN 9910
SPECIAL TESTING IS USED TO INDICATE THIS
REQUIREMENT.
THE CONTRACTOR MUST PROVIDE COPIES OF MANGANESE
PHOSPHATE COATING
PROCEDURES WRITTEN SPECIFICALLY FOR THE COATING OF
PARTS ON THIS
CONTRACT TO THE PCO WITHIN 45 DAY AFTER AWARD.
(EMAIL: PCO AND THE
PHOSPHATE MAILBOX AT: DSCC PHOSPHATE PROCEDURE
[email protected])
PRODUCT INSPECTION WILL OCCUR AT THE ACTUAL
MANUFACTURER'S FACILITY AND
IN PROCESS INSPECTIONS WILL OCCUR AT THE PHOSPHATE
CONTRACTOR'S FACILITY
IDENTIFIED ON THIS CONTRACT. ANY CHANGES MUST BE
APPROVED BY THE PCO.
ASSURE THAT THE PHOSPHATE CONTRACTOR SELECTED TO
PLATE THE PARTS FOR
THIS CONTRACT HAS BEEN ASSIGNED A DCMA QAR BY
LETTER OF DELEGATION (LOD)
FOR GOVERNMENT SOURCE INSPECTION (GSI) BY THE
PRIME QAR. OVERSIGHT IS
REQUIRED DURING THE PLATING PROCESS TO VERIFY
CONFORMANCE TO THE DSCC
APPROVED PHOSPHATE PROCEDURE.
PRODUCT VERIFICATION TESTING (PVT) CLAUSE DLAD
52.246-9004 MAY BE
INVOKED FOR THE REFERENCED CONTRACT. IF INVOKED,
PVT SAMPLES MUST BE
INSPECTED, PACKAGED AND MARKED AS REQUIRED IN THE
CONTRACT. ONE (1)
SAMPLE MAY BE DESTROYED DURING TESTING.
PRODUCT VERIFICATION TESTING, IF INVOKED, WILL BE
PERFORMED PRIOR TO
ACCEPTANCE OF EACH SHIPMENT. THE CONTRACTOR MUST
PROVIDE PVT SAMPLES
FROM EACH SUBCONTRACTOR AND FROM EACH PHOSPHATE
CONTRACTOR USED IN THE
PRODUCTION OF PARTS ON THIS CONTRACT. FIVE (5) PVT
SAMPLES WILL BE
REQUIRED TO BE IDENTIFIED TO THOSE SUBCONTRACTORS
AND PHOSPHATE
CONTRACTORS WHEN THEY ARE SENT IN FOR TESTING.

DRAWING PACKAGE CITED IS SUBJECT TO
EXPORT-CONTROL
REGULATIONS AND DISTRIBUTION IS LIMITED TO THOSE
CONTRACTORS QUALIFIED THROUGH JCP CERTIFICATION.
TO APPLY FOR CERTIFICATION, COMPLETE DD FORM
2345, "MILITARY CRITICAL TECHNICAL DATA
AGREEMENT." FORM IS AVAILABLE AT THE WORLD
WIDE WEB ADDRESS HTTP://WWW.DLIS.DLA.MIL/JCP
OR BY WRITING TO:

UNITED STATES/CANADA JOINT CERTIFICATION OFFICE
DEFENSE LOGISITICS INFORMATION SERVICE
FEDERAL CENTER
74 WASHINGTON AVE,NORTH
BATTLE CREEK, MI 49017-3084.

CONTRACTS WILL BE AWARDED ONLY TO THOSE
CONTRACTORS WITH JCP CERTIFICATION ISSUED
PRIOR TO AN AWARD.

"THE DATA RELEASED PURSUANT TO THIS PROCUREMENT
WAS FURNISHED UNDER A LIMITED USE LICENSE
AGREEMENT WITH FABRIQUE NATIONALE HERSTAL (FNH),
DAAA09-C-2018 FOR GOVERNMENT USE IN THE
MANUFACTURE OF THESE ITEMS. ANY USE CONTRARY TO
DFARS 252.227-7025 WILL GIVE RISE TO THIRD PARTY
BENEFICIARY RIGHTS OF FNH."

CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE
USED NOR INCORPORATED IN ANY ITEMS TO BE
DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION
SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT
DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.
SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR
APPROVAL UNLESS THEY ARE AUTHORIZED BY THE
SPECIFICATION REQUIREMENTS.

DLAD 52.246-9003, MEASURING AND TEST EQUIPMENT,
APPLIES.

DLAD CLAUSE 52.246-9004,PRODUCT VERIFICATION
TESTING,IS HEREBY INCORPORATED,AND MAY BE
INVOKED AT THE DISCRETION OF THE PROCUREMENT
ACTIVITY.

IF AQLS ARE LISTED IN THE SPECIFICATION(S)
OR DRAWING(S) THEY MAY BE USED TO ESTABLISH THE
AUTHORIZED SAMPLE SIZE,HOWEVER,THE ACCEPTANCE
NUMBER FOR THIS CONTRACT IS ZERO;I.E.,THIS
CONTRACT REQUIRES A SAMPLING PLAN THAT ACCEPTS
ON ZERO DEFECTS AND REJECTS ON ONE OR MORE
DEFECT(S).

THE INTERNATIONAL ORGANIZATION FOR
STANDARDIZATION (ISO) 9002 OR A "TAILORED"
PROGRAM MEETING THE FOLLOWING ISO 9002
PARAGRAPHS APPLIES:
4.5, DOCUMENT CONTROL: LIMITED TO INSPECTION
AND TESTING AS WELL AS APPLICABLE DRAWINGS,
SPECIFICATIONS AND INSTRUCTIONS REQUIRED BY
CONTRACT
4.6, PURCHASING: 4.6.1 AND LIMITED TO 4.6.2 A)
AND 4.6.4.2, ALL OTHER PARTS OF PARAGRAPH
ARE HEREBY DELETED
4.7, CUSTOMER-SUPPLIED PRODUCT:
4.8, PRODUCT IDENTIFICATION & TRACEABILITY:
4.10, INSPECTION & TESTING:
4.11, INSPECTION, MEASURING & TEST EQUIPMENT:
4.12, INSPECTION AND TEST STATUS:
4.13, CONTROL OF NONCONFORMING PRODUCT:
4.14, CORRECTIVE AND PREVENTIVE ACTION:
PARAGRAPH 4.14.3 APPLY TO PRODUCT ONLY
4.16, QUALITY RECORDS:
FAR CLAUSE 52.246-11 APPLIES

MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL
NOT BE INTENTIONALLY ADDED TO,OR COME IN DIRECT
CONTACT WITH,ANY HARDWARE OR SUPPLIES FURNISHED
UNDER THIS CONTRACT.

THIS NSN CONTAINS ONE OR MORE COMPONENTS WHICH
MUST MEET QPL/QML SPECIFICATIONS.BY SUBMITTING
AN OFFER, THE OFFEROR AGREES TO PROVIDE QPL/QML
COMPONENTS ONLY FROM SOURCES QUALIFIED ON THE
APPLICABLE QPL(S)/QML(S).