Fire Fighter Turnout Coat, Isotemp Fire Wolf 4-Ply Model 8001. Manufactured from PBI (R)-Matrix, yellow, anti-static Kevlar 205g/sqm with membrane 130 g/sqm and Nomex/Kevlar heat barrier 205 g/sqm. The protective clothing shall meet the standard EN 469:2005/06, Level 2 (Xf2, Xr2, Y 2, Z 2) CE 0516 + 0555, Z 3253/07-4339/07 + 06.0.44924 Pyromaniac-Test and shall be approved by NFPA. Furthermore the coat shall be equipped with the following features: - Stand up collar with Velcro closure. - Inner closure with heavy duty zipper -Water and Chemical resistant (WOR) - Storm flap overlapping construction with Velcro. - Inside pocket right hand - Slide pocket on the left side over the chest with opening between storm flap equipped with inside Velcro closure . - Radio pocket on the right side with Velcro radio flap and provision for antenna, fixing loops for the antenna above the pocket, one side closed firm other side to open with Velcro and one closed above. - Velcro provision for nametag, on the left side. - Nametag: black background silver writing. - Names will be provided. - 2 oversized inside pockets with Velcro closure. One pocket with an internal small pocket for rescue knife storage. - Hook inside right and left pocket. - Sleeves with adjustment zippers. - Nomex wristlets with thumb holes sewn to outer shell and thermal liner. - Shoulder collar in two different colors to be fastened on the coat, embroidered, USAG BAVARIA FIRE RESCUE. - Colors of collar: blue, collar to be fastened on jacket in a manner that it does not interfere with the use of SCBA equipment -Retro Reflective Trim 3M yellow-silver-yellow, 50 mm and 76 mm, sewn on firm. 76 mm trim: Horizontal under the radio pocket closure, around the sleeves, vertical on the back. 50 mm trim: Around the hem. -jacket with dead air ventilation system. Or equivalent.

Fire Fighter Turnout Pants, Isotemp Fire Wolf 3-Ply Model 8002. Manufactured from PBI (R)-Matrix, yellow, anti-static Kevlar 205g/sqm with membrane 130 g/sqm and Nomex/Kevlar heat barrier 205 g/sqm. The protective clothing shall meet the standard EN 469:2005/06, Level 2 (Xf2, Xr2, Y 2, Z 2) CE 0516 + 0555, Z 3253/07-4339/07 + 06.0.44924 Pyromaniac-Test and shall be approved by NFPA. Furthermore the pants shall be equipped with the following features:
- High waist pants - Removable 45 mm wide over cross sewed heavy duty suspenders supported with leather and knop holes (3ea) - Front fly with overlapping design, Velcro and hook & dee closure (carabiner opening showing towards body) - Reinforced crotch - Adjustable waist with Velcro adjuster lab on the back. - 2 oversized bellow pockets with Velcro closure one pocket with internal pocket for Mag Lite - Kevlar reinforced knee pads covered inside 20 cm high as a moister and dirt barrier knee protection (outside) KEVLAR covered by PBI material.. -Provision for marking of ownership. -Retro Reflective Trim 3M, yellow-silver-yellow, 50 mm and 75 mm, sewn on firm. 75 mm trim: One time around the legs, 15 cm above the hem. 50 mm trim: One time vertical, on the bottom of the legs at the backside. Or equivalent.

Flame Protection Hood. 1. PBI gold, sand/yellow - Stretchable for easy pull over and save fit - Layer over chest, back and collar - Seamless at the chin area - Flat seams - Elastic face opening - NFPA 1972 and EN469 certified. Or equivalent.