20'X30' Composite Lumber Rectangle Gazeb
FFP
Vendor shall provide and install a 20'X30' Composite Lumber Rectangular Gazebo
with the following components:
Posts
Treated Pine with Composite Wrap - Color TBD
Composite Deck - Color TBD
1-1/2" Round Spindle Railings
Standard Braces
1x3 Standard Top Railing Sections
No Cupola
No Screens
No Ceiling - Treated Pine Tongue & Groove Roof Decking/Rafters
Old English Pewter Asphalt Shingles
No Fan
Installation on a Prepared Site
Product will ship as a kit.
Composite Lumber only will be accepted
*No refurbished materials
Vendor shall provide any drawings and material fact sheet
FOB: Destination
SIGNAL CODE: A


CLAUSES INCORPORATED BY REFERENCE
52.212-4 Contract Terms and Conditions--Commercial Items JAN 2017
252.204-7012 Safeguarding Covered Defense Information and Cyber
Incident Reporting
OCT 2016
252.232-7003 Electronic Submission of Payment Requests and Receiving
Reports
JUN 2012
CLAUSES INCORPORATED BY FULL TEXT
52.212-5 CONTRACT TERMS AND CONDITIONS REQUIRED TO IMPLEMENT STATUTES OR
EXECUTIVE ORDERS--COMMERCIAL ITEMS (JAN 2017)
(a) The Contractor shall comply with the following Federal Acquisition Regulation (FAR) clauses, which are
incorporated in this contract by reference, to implement provisions of law or Executive orders applicable to
acquisitions of commercial items:
(1) 52.203-19, Prohibition on Requiring Certain Internal Confidentiality Agreements or Statements (JAN 2017)
(section 743 of Division E, Title VII, of the Consolidated and Further Continuing Appropriations Act, 2015 (Pub. L.
113-235) and its successor provisions in subsequent appropriations acts (and as extended in continuing resolutions)).
(2) 52.209-10, Prohibition on Contracting with Inverted Domestic Corporations (Nov 2015).
(3) 52.233-3, Protest After Award (AUG 1996) (31 U.S.C. 3553).
(4) 52.233-4, Applicable Law for Breach of Contract Claim (OCT 2004) (Public Laws 108-77 and 108-78 (19
U.S.C. 3805 note)).
(b) The Contractor shall comply with the FAR clauses in this paragraph (b) that the Contracting Officer has
indicated as being incorporated in this contract by reference to implement provisions of law or Executive orders
applicable to acquisitions of commercial items: (Contracting Officer check as appropriate.)
___ (1) 52.203-6, Restrictions on Subcontractor Sales to the Government (Sept 2006), with Alternate I (Oct 1995)
(41 U.S.C. 4704 and 10 U.S.C. 2402).
X (2) 52.203-13, Contractor Code of Business Ethics and Conduct (Oct 2015) (41 U.S.C. 3509).
W912KN-17-T-0034
Page 5 of 24
____ (3) 52.203-15, Whistleblower Protections under the American Recovery and Reinvestment Act of 2009 (June
2010) (Section 1553 of Pub. L. 111-5). (Applies to contracts funded by the American Recovery and Reinvestment
Act of 2009.)
___ (4) 52.204-10, Reporting Executive Compensation and First-Tier Subcontract Awards (Oct 2016) (Pub. L. 109-
282) (31 U.S.C. 6101 note).
___ (5) [Reserved]
___ (6) 52.204-14, Service Contract Reporting Requirements (Oct 2016) (Pub. L. 111-117, section 743 of Div.
C).
___ (7) 52.204-15, Service Contract Reporting Requirements for Indefinite-Delivery Contracts (Oct 2016) (Pub.
L. 111-117, section 743 of Div. C).
___ (8) 52.209-6, Protecting the Government's Interest When Subcontracting with Contractors Debarred,
Suspended, or Proposed for Debarment. (Oct 2015) (31 U.S.C. 6101 note).
____ (9) 52.209-9, Updates of Publicly Available Information Regarding Responsibility Matters (July 2013) (41
U.S.C. 2313).
____ (10) [Reserved]
____ (11)(i) 52.219-3, Notice of HUBZone Set-Aside or Sole-Source Award (NOV 2011) (15 U.S.C. 657a).
____ (ii) Alternate I (NOV 2011) of 52.219-3.
____ (12) (i) 52.219-4, Notice of Price Evaluation Preference for HUBZone Small Business Concerns (OCT 2014)
(if the offeror elects to waive the preference, it shall so indicate in its offer) (15 U.S.C. 657a).
____ (ii) Alternate I (JAN 2011) of 52.219-4.
____ (13) [Reserved]
X (14)(i) 52.219-6, Notice of Total Small Business Set-Aside (NOV 2011) (15 U.S.C. 644).
____ (ii) Alternate I (NOV 2011).
____ (iii) Alternate II (NOV 2011).
____ (15)(i) 52.219-7, Notice of Partial Small Business Set-Aside (June 2003) (15 U.S.C. 644).
____ (ii) Alternate I (Oct 1995) of 52.219-7.
____ (iii) Alternate II (Mar 2004) of 52.219-7.
X (16) 52.219-8, Utilization of Small Business Concerns (Nov 2016) (15 U.S.C. 637(d)(2) and (3)).
____ (17)(i) 52.219-9, Small Business Subcontracting Plan (Jan 2017) (15 U.S.C. 637(d)(4)).
____ (ii) Alternate I (Nov 2016) of 52.219-9.
____ (iii) Alternate II (Nov 2016) of 52.219-9.
W912KN-17-T-0034
Page 6 of 24
____ (iv) Alternate III (Nov 2016) of 52.219-9.
____ (v) Alternate IV (Nov 2016) of 52.219-9.
____ (18) 52.219-13, Notice of Set-Aside of Orders (NOV 2011) (15 U.S.C. 644(r)).
____ (19) 52.219-14, Limitations on Subcontracting (JAN 2017) (15 U.S.C. 637(a)(14)).
____ (20) 52.219-16, Liquidated Damages-Subcon-tracting Plan (Jan 1999) (15 U.S.C. 637(d)(4)(F)(i)).
____ (21) 52.219-27, Notice of Service-Disabled Veteran-Owned Small Business Set-Aside (NOV 2011) (15 U.S.C.
657f).
____ (22) 52.219-28, Post Award Small Business Program Rerepresentation (July 2013) (15 U.S.C. 632(a)(2)).
____ (23) 52.219-29, Notice of Set-Aside for, or Sole Source Award to, Economically Disadvantaged Women-
Owned Small Business Concerns (Dec 2015) (15 U.S.C. 637(m)).
____(24) 52.219-30, Notice of Set-Aside for, or Sole Source Award to, Women-Owned Small Business Concerns
Eligible Under the Women-Owned Small Business Program (Dec 2015) (15 U.S.C. 637(m)).
____ (25) 52.222-3, Convict Labor (June 2003) (E.O. 11755).
____(26) 52.222-19, Child Labor--Cooperation with Authorities and Remedies (Oct 2016) (E.O. 13126).
____ (27) 52.222-21, Prohibition of Segregated Facilities (Apr 2015).
X (28) 52.222-26, Equal Opportunity (Sept 2016) (E.O. 11246).
____ (29) 52.222-35, Equal Opportunity for Veterans (Oct 2015) (38 U.S.C. 4212).
____ (30) 52.222-36, Equal Opportunity for Workers with Disabilities (July 2014) (29 U.S.C. 793).
____ (31) 52.222-37, Employment Reports on Veterans (FEB 2016) (38 U.S.C. 4212).
____ (32) 52.222-40, Notification of Employee Rights Under the National Labor Relations Act (Dec 2010) (E.O.
13496).
X (33)(i) 52.222-50, Combating Trafficking in Persons (March 2, 2015) (22 U.S.C. chapter 78 and E.O. 13627).
____ (ii) Alternate I (March 2, 2015) of 52.222-50 (22 U.S.C. chapter 78 and E.O. 13627).
____ (34) 52.222-54, Employment Eligibility Verification (Oct 2015). (E. O. 12989). (Not applicable to the
acquisition of commercially available off-the-shelf items or certain other types of commercial items as prescribed in
22.1803.)
____ (35) 52.222-59, Compliance with Labor Laws (Executive Order 13673) (OCT 2016). (Applies at $50 million
for solicitations and resultant contracts issued from October 25, 2016 through April 24, 2017; applies at $500,000
for solicitations and resultant contracts issued after April 24, 2017).
Note to paragraph (b)(35): By a court order issued on October 24, 2016, 52.222-59 is enjoined indefinitely as of
the date of the order. The enjoined paragraph will become effective immediately if
the court terminates the injunction. At that time, DoD, GSA, and NASA will publish a document in the Federal
Register advising the public of the termination of the injunction.
W912KN-17-T-0034
Page 7 of 24
____ (36) 52.222-60, Paycheck Transparency (Executive Order 13673) (OCT 2016).
____ (37)(i) 52.223-9, Estimate of Percentage of Recovered Material Content for EPA-Designated Items (May
2008) (42 U.S.C. 6962(c)(3)(A)(ii)). (Not applicable to the acquisition of commercially available off-the-shelf
items.)
____ (ii) Alternate I (May 2008) of 52.223-9 (42 U.S.C. 6962(i)(2)(C)). (Not applicable to the acquisition of
commercially available off-the-shelf items.)
____ (38) 52.223-11, Ozone-Depleting Substances and High Global Warming Potential Hydrofluorocarbons (June,
2016) (E.O. 13693).
____ (39) 52.223-12, Maintenance, Service, Repair, or Disposal of Refrigeration Equipment and Air Conditioners
(June, 2016) (E.O. 13693).
____ (40) (i) 52.223-13, Acquisition of EPEAT® Registered Imaging Equipment (Jun 2014) (E.O.s 13423 and
13514).
____ (ii) Alternate I (OCT 2015) of 52.223-13.
____ (41)(i) 52.223-14, Acquisition of EPEAT® Registered Televisions (Jun 2014) (E.O.s 13423 and 13514).
____ (ii) Alternate I (Jun 2014) of 52.223-14.
____ (42) 52.223-15, Energy Efficiency in Energy-Consuming Products (Dec 2007) (42 U.S.C. 8259b).
____ (43)(i) 52.223-16, Acquisition of EPEAT[supreg]-Registered Personal Computer Products (OCT 2015) (E.O.s
13423 and 13514).
____ (ii) Alternate I (Jun 2014) of 52.223-16.
____ (44) 52.223-18, Encouraging Contractor Policies to Ban Text Messaging While Driving (Aug 2011) (E.O.
13513).
____ (45) 52.223-20, Aerosols (June, 2016) (E.O. 13693).
____ (46) 52.223-21, Foams (June, 2016) (E.O. 13693).
____ (47)(i) 52.224-3, Privacy Training (JAN 2017) (5 U.S.C. 552a).
____ (ii) Alternate I (JAN 2017) of 52.224-3.
X (48) 52.225-1, Buy American--Supplies (May 2014) (41 U.S.C. chapter 83).
____(49) (i) 52.225-3, Buy American--Free Trade Agreements--Israeli Trade Act (May 2014) (41 U.S.C. chapter
83, 19 U.S.C. 3301 note, 19 U.S.C. 2112 note, 19 U.S.C. 3805 note, 19 U.S.C. 4001 note, Pub. L.
103-182, 108-77, 108-78, 108-286, 108-302, 109-53, 109-169, 109-283, 110-138, 112-41, 112-42, and 112-43.
____ (ii) Alternate I (May 2014) of 52.225-3.
____ (iii) Alternate II (May 2014) of 52.225-3.
____ (iv) Alternate III (May 2014) of 52.225-3.
____ (50) 52.225-5, Trade Agreements (Oct 2016) (19 U.S.C. 2501, et seq., 19 U.S.C. 3301 note).
W912KN-17-T-0034
Page 8 of 24
____ (51) 52.225-13, Restrictions on Certain Foreign Purchases (June 2008) (E.O.'s, proclamations, and statutes
administered by the Office of Foreign Assets Control of the Department of the Treasury).
____ (52) 52.225-26, Contractors Performing Private Security Functions Outside the United States (Oct 2016)
(Section 862, as amended, of the National Defense Authorization Act for Fiscal Year 2008; 10 U.S.C. 2302 Note).
____ (53) 52.226-4, Notice of Disaster or Emergency Area Set-Aside (Nov 2007) (42 U.S.C. 5150
____ (54) 52.226-5, Restrictions on Subcontracting Outside Disaster or Emergency Area (Nov 2007) (42 U.S.C.
5150).
____ (55) 52.232-29, Terms for Financing of Purchases of Commercial Items (Feb 2002) (41 U.S.C. 4505, 10
U.S.C. 2307(f)).
____ (56) 52.232-30, Installment Payments for Commercial Items (Jan 2017) (41 U.S.C. 4505, 10 U.S.C. 2307(f)).
X (57) 52.232-33, Payment by Electronic Funds Transfer-System for Award Management (July 2013) (31 U.S.C.
3332).
____ (58) 52.232-34, Payment by Electronic Funds Transfer-Other than System for Award Management (July
2013) (31 U.S.C. 3332).
____ (59) 52.232-36, Payment by Third Party (MAY 2014) (31 U.S.C. 3332).
____ (60) 52.239-1, Privacy or Security Safeguards (Aug 1996) (5 U.S.C. 552a).
____ (61) 52.242-5, Payments to Small Business Subcontractors (JAN 2017)(15 U.S.C. 637(d)(12)).
____ (62)(i) 52.247-64, Preference for Privately Owned U.S.-Flag Commercial Vessels (Feb 2006) (46 U.S.C.
Appx. 1241(b) and 10 U.S.C. 2631).
____ (ii) Alternate I (Apr 2003) of 52.247-64.
(c) The Contractor shall comply with the FAR clauses in this paragraph (c), applicable to commercial services, that
the Contracting Officer has indicated as being incorporated in this contract by reference to implement provisions of
law or Executive orders applicable to acquisitions of commercial items: (Contracting Officer check as appropriate.)
_____(1) 52.222-17, Nondisplacement of Qualified Workers (May 2014) (E.O. 13495).
_____ (2) 52.222-41, Service Contract Labor Standards (MAY 2014) (41 U.S.C. chapter 67).
_____ (3) 52.222-42, Statement of Equivalent Rates for Federal Hires (MAY 2014) (29 U.S.C. 206 and 41 U.S.C.
chapter 67).
_____ (4) 52.222-43, Fair Labor Standards Act and Service Contract Labor Standards--Price Adjustment (Multiple
Year and Option Contracts) (MAY 2014) (29 U.S.C. 206 and 41 U.S.C. chapter 67).
_____ (5) 52.222-44, Fair Labor Standards Act and Service Contract Labor Standards--Price Adjustment (MAY
2014) (29 U.S.C 206 and 41 U.S.C. chapter 67).
_____ (6) 52.222-51, Exemption from Application of the Service Contract Labor Standards to Contracts for
Maintenance, Calibration, or Repair of Certain Equipment--Requirements (MAY 2014) (41 U.S.C. chapter 67).
W912KN-17-T-0034
Page 9 of 24
_____ (7) 52.222-53, Exemption from Application of the Service Contract Labor Standards to Contracts for Certain
Services--Requirements (MAY 2014) (41 U.S.C. chapter 67).
_____(8) 52.222-55, Minimum Wages Under Executive Order 13658 (DEC 2015) (E.O. 13658).
_____ (9) 52.222-62, Paid Sick Leave Under Executive Order 13706 (JAN 2017) (E.O. 13706).
_____ (10) 52.226-6, Promoting Excess Food Donation to Nonprofit Organizations (MAY 2014) (42 U.S.C. 1792).
_____ (11) 52.237-11, Accepting and Dispensing of $1 Coin (Sept 2008) (31 U.S.C. 5112(p)(1)).
(d) Comptroller General Examination of Record. The Contractor shall comply with the provisions of this paragraph
(d) if this contract was awarded using other than sealed bid, is in excess of the simplified acquisition threshold, and
does not contain the clause at 52.215-2, Audit and Records--Negotiation.
(1) The Comptroller General of the United States, or an authorized representative of the Comptroller General, shall
have access to and right to examine any of the Contractor's directly pertinent records involving transactions related
to this contract.
(2) The Contractor shall make available at its offices at all reasonable times the records, materials, and other
evidence for examination, audit, or reproduction, until 3 years after final payment under this contract or for any
shorter period specified in FAR Subpart 4.7, Contractor Records Retention, of the other clauses of this contract. If
this contract is completely or partially terminated, the records relating to the work terminated shall be made
available for 3 years after any resulting final termination settlement. Records relating to appeals under the disputes
clause or to litigation or the settlement of claims arising under or relating to this contract shall be made available
until such appeals, litigation, or claims are finally resolved.
(3) As used in this clause, records include books, documents, accounting procedures and practices, and other data,
regardless of type and regardless of form. This does not require the Contractor to create or maintain any record that
the Contractor does not maintain in the ordinary course of business or pursuant to a provision of law.
(e) (1) Notwithstanding the requirements of the clauses in paragraphs (a), (b), (c), and (d) of this clause, the
Contractor is not required to flow down any FAR clause, other than those in this paragraph (e)(1)in a subcontract for
commercial items. Unless otherwise indicated below, the extent of the flow down shall be as required by the
clause-
(i) 52.203-13, Contractor Code of Business Ethics and Conduct (Oct 2015) (41 U.S.C. 3509).
(ii) 52.203-19, Prohibition on Requiring Certain Internal Confidentiality Agreements or Statements (JAN 2017)
(section 743 of Division E, Title VII, of the Consolidated and Further Continuing Appropriations Act, 2015 (Pub. L.
113-235) and its successor provisions in subsequent appropriations acts (and as extended in continuing resolutions)).
(iii) 52.219-8, Utilization of Small Business Concerns (Nov 2016) (15 U.S.C. 637(d)(2) and (3)), in all subcontracts
that offer further subcontracting opportunities. If the subcontract (except subcontracts to small business concerns)
exceeds $700,000 ($1.5 million for construction of any public facility), the subcontractor must include 52.219-8 in
lower tier subcontracts that offer subcontracting opportunities.
(iv) 52.222-17, Nondisplacement of Qualified Workers (MAY 2014) (E.O. 13495). Flow down required in
accordance with paragraph (l) of FAR clause 52.222-17.
(v) 52.222-21, Prohibition of Segregated Facilities (Apr 2015).
(vi) 52.222-26, Equal Opportunity (Sept 2016) (E.O. 11246).
(vii) 52.222-35, Equal Opportunity for Veterans (Oct 2015) (38 U.S.C. 4212).
W912KN-17-T-0034
Page 10 of 24
(viii) 52.222-36, Equal Opportunity for Workers with Disabilities (Jul 2014) (29 U.S.C. 793).
(ix) 52.222-37, Employment Reports on Veterans (Feb 2016) (38 U.S.C. 4212).
(x) 52.222-40, Notification of Employee Rights Under the National Labor Relations Act (Dec 2010) (E.O. 13496).
Flow down required in accordance with paragraph (f) of FAR clause 52.222-40.
(xi) 52.222-41, Service Contract Labor Standards (May 2014), (41 U.S.C. chapter 67).
(xii) _____ (A) 52.222-50, Combating Trafficking in Persons (March 2, 2015) (22 U.S.C. chapter 78 and E.O.
13627).
_____ (B) Alternate I (March 2, 2015) of 52.222-50 (22 U.S.C. chapter 78 and E.O. 13627).
(xiii) 52.222-51, Exemption from Application of the Service Contract Labor Standards to Contracts for
Maintenance, Calibration, or Repair of Certain Equipment--Requirements (May 2014) (41 U.S.C. chapter 67.)
(xiv) 52.222-53, Exemption from Application of the Service Contract Labor Standards to Contracts for Certain
Services--Requirements (May 2014) (41 U.S.C. chapter 67)
(xv) 52.222-54, Employment Eligibility Verification (Oct 2015) (E. O. 12989).
(xvi)52.222-55, Minimum Wages Under Executive Order 13658 (Dec 2015) (E.O. 13658).
(xvii) 52.222-59, Compliance with Labor Laws (Executive Order 13673) (OCT 2016) (Applies at $50 million for
solicitations and resultant contracts issued from October 25, 2016 through April 24, 2017; applies at $500,000 for
solicitations and resultant contracts issued after April 24, 2017).
Note to paragraph (e)(1)(xvii): By a court order issued on October 24, 2016, 52.222-59 is enjoined indefinitely as
of the date of the order. The enjoined paragraph will become effective immediately if the court terminates the
injunction. At that time, DoD, GSA, and NASA will publish a document in the Federal Register advising the public
of the termination of the injunction.
(xviii) 52.222-60, Paycheck Transparency (Executive Order 13673) (OCT 2016)).
(xix) (A) 52.224-3, Privacy Training (JAN 2017) (5 U.S.C. 552a).
(B) Alternate I (JAN 2017) of 52.224-3.
(xx) 52.222-62 Paid Sick Leave Under Executive Order 13706 (JAN 2017) (E.O. 13706).
(xxi) 52.225-26, Contractors Performing Private Security Functions Outside the United States (Oct 2016) (Section
862, as amended, of the National Defense Authorization Act for Fiscal Year 2008; 10 U.S.C. 2302 Note).
(xxii) 52.226-6, Promoting Excess Food Donation to Nonprofit Organizations. (May 2014) (42 U.S.C. 1792). Flow
down required in accordance with paragraph (e) of FAR clause 52.226-6.
(xxiii) 52.247-64, Preference for Privately-Owned U.S. Flag Commercial Vessels (Feb 2006) (46 U.S.C. Appx
1241(b) and 10 U.S.C. 2631). Flow down required in accordance with paragraph (d) of FAR clause 52.247-64.
W912KN-17-T-0034
Page 11 of 24
(2) While not required, the Contractor may include in its subcontracts for commercial items a minimal number of
additional clauses necessary to satisfy its contractual obligations.
(End of clause)
52.222-50 COMBATING TRAFFICKING IN PERSONS (MAR 2015)
(a) Definitions. As used in this clause--
Agent means any individual, including a director, an officer, an employee, or an independent contractor, authorized
to act on behalf of the organization.
Coercion means--
(1) Threats of serious harm to or physical restraint against any person;
(2) Any scheme, plan, or pattern intended to cause a person to believe that failure to perform an act would result in
serious harm to or physical restraint against any person; or
(3) The abuse or threatened abuse of the legal process.
Commercially available off-the-shelf (COTS) item means--
(1) Any item of supply (including construction material) that is--
(i) A commercial item (as defined in paragraph (1) of the definition at FAR 2.101);
(ii) Sold in substantial quantities in the commercial marketplace; and
(iii) Offered to the Government, under a contract or subcontract at any tier, without modification, in the same form
in which it is sold in the commercial marketplace; and
(2) Does not include bulk cargo, as defined in 46 U.S.C. 40102(4), such as agricultural products and petroleum
products.
Commercial sex act means any sex act on account of which anything of value is given to or received by any person.
Debt bondage means the status or condition of a debtor arising from a pledge by the debtor of his or her personal
services or of those of a person under his or her control as a security for debt, if the value of those services as
reasonably assessed is not applied toward the liquidation of the debt or the length and nature of those services are
not respectively limited and defined.
Employee means an employee of the Contractor directly engaged in the performance of work under the contract who
has other than a minimal impact or involvement in contract performance.
Forced Labor means knowingly providing or obtaining the labor or services of a person--
(1) By threats of serious harm to, or physical restraint against, that person or another person;
W912KN-17-T-0034
Page 12 of 24
(2) By means of any scheme, plan, or pattern intended to cause the person to believe that, if the person did not
perform such labor or services, that person or another person would suffer serious harm or physical restraint; or
(3) By means of the abuse or threatened abuse of law or the legal process.
Involuntary servitude includes a condition of servitude induced by means of--
(1) Any scheme, plan, or pattern intended to cause a person to believe that, if the person did not enter into or
continue in such conditions, that person or another person would suffer serious harm or physical restraint; or
(2) The abuse or threatened abuse of the legal process.
Severe forms of trafficking in persons means--
(1) Sex trafficking in which a commercial sex act is induced by force, fraud, or coercion, or in which the person
induced to perform such act has not attained 18 years of age; or
(2) The recruitment, harboring, transportation, provision, or obtaining of a person for labor or services, through the
use of force, fraud, or coercion for the purpose of subjection to involuntary servitude, peonage, debt bondage, or
slavery.
Sex trafficking means the recruitment, harboring, transportation, provision, or obtaining of a person for the purpose
of a commercial sex act.
Subcontract means any contract entered into by a subcontractor to furnish supplies or services for performance of a
prime contract or a subcontract.
Subcontractor means any supplier, distributor, vendor, or firm that furnishes supplies or services to or for a prime
contractor or another subcontractor.
United States means the 50 States, the District of Columbia, and outlying areas.
(b) Policy. The United States Government has adopted a policy prohibiting trafficking in persons including the
trafficking-related activities of this clause. Contractors, contractor employees, and their agents shall not--
(1) Engage in severe forms of trafficking in persons during the period of performance of the contract;
(2) Procure commercial sex acts during the period of performance of the contract;
(3) Use forced labor in the performance of the contract;
(4) Destroy, conceal, confiscate, or otherwise deny access by an employee to the employee's identity or immigration
documents, such as passports or drivers' licenses, regardless of issuing authority;
(5)(i) Use misleading or fraudulent practices during the recruitment of employees or offering of employment, such
as failing to disclose, in a format and language accessible to the worker,
basic information or making material misrepresentations during the recruitment of employees regarding the key
terms and conditions of employment, including wages and fringe benefits, the location of work, the living
conditions, housing and associated costs (if employer or agent provided or arranged), any significant cost to be
charged to the employee, and, if applicable, the hazardous nature of the work;
(ii) Use recruiters that do not comply with local labor laws of the country in which the recruiting takes place;
(6) Charge employees recruitment fees;
W912KN-17-T-0034
Page 13 of 24
(7)(i) Fail to provide return transportation or pay for the cost of return transportation upon the end of employment--
(A) For an employee who is not a national of the country in which the work is taking place and who was brought
into that country for the purpose of working on a U.S. Government contract or subcontract (for portions of contracts
performed outside the United States); or
(B) For an employee who is not a United States national and who was brought into the United States for the purpose
of working on a U.S. Government contract or subcontract, if the payment of such costs is required under existing
temporary worker programs or pursuant to a written agreement with the employee (for portions of contracts
performed inside the United States); except that--
(ii) The requirements of paragraphs (b)(7)(i) of this clause shall not apply to an employee who is--
(A) Legally permitted to remain in the country of employment and who chooses to do so; or
(B) Exempted by an authorized official of the contracting agency from the requirement to provide return
transportation or pay for the cost of return transportation;
(iii) The requirements of paragraph (b)(7)(i) of this clause are modified for a victim of trafficking in persons who is
seeking victim services or legal redress in the country of employment, or for a witness in an
enforcement action related to trafficking in persons. The contractor shall provide the return transportation or pay the
cost of return transportation in a way that does not obstruct the victim services, legal redress, or witness activity. For
example, the contractor shall not only offer return transportation to a witness at a time when the witness is still
needed to testify. This paragraph does not apply when the exemptions at paragraph (b)(7)(ii) of this clause apply.
(8) Provide or arrange housing that fails to meet the host country housing and safety standards; or
(9) If required by law or contract, fail to provide an employment contract, recruitment agreement, or other required
work document in writing. Such written work document shall be in a language the employee understands. If the
employee must relocate to perform the work, the work document shall be provided to the employee at least five days
prior to the employee relocating. The employee's work document shall include, but is not limited to, details about
work description, wages, prohibition on charging
recruitment fees, work location(s), living accommodations and associated costs, time off, roundtrip transportation
arrangements, grievance process, and the content of applicable laws and regulations that prohibit trafficking in
persons.
(c) Contractor requirements. The Contractor shall--
(1) Notify its employees and agents of--
(i) The United States Government's policy prohibiting trafficking in persons, described in paragraph (b) of this
clause; and
(ii) The actions that will be taken against employees or agents for violations of this policy. Such actions for
employees may include, but are not limited to, removal from the contract, reduction in benefits, or termination of
employment; and
(2) Take appropriate action, up to and including termination, against employees, agents, or subcontractors that
violate the policy in paragraph (b) of this clause.
(d) Notification. (1) The Contractor shall inform the Contracting Officer and the agency Inspector General
immediately of--
(i) Any credible information it receives from any source (including host country law enforcement) that alleges a
Contractor employee, subcontractor, subcontractor employee, or their agent has engaged in conduct that violates the
W912KN-17-T-0034
Page 14 of 24
policy in paragraph (b) of this clause (see also 18 U.S.C. 1351, Fraud in Foreign Labor Contracting, and 52.203-
13(b)(3)(i)(A), if that clause is included in the
solicitation or contract, which requires disclosure to the agency
Office of the Inspector General when the Contractor has credible
evidence of fraud); and
(ii) Any actions taken against a Contractor employee,
subcontractor, subcontractor employee, or their agent pursuant to
this clause.
(2) If the allegation may be associated with more than one
contract, the Contractor shall inform the contracting officer for
the contract with the highest dollar value.
(e) Remedies. In addition to other remedies available to the
Government, the Contractor's failure to comply with the requirements
of paragraphs (c), (d), (g), (h), or (i) of this clause may result
in--
(1) Requiring the Contractor to remove a Contractor employee or employees from the performance of the contract;
(2) Requiring the Contractor to terminate a subcontract;
(3) Suspension of contract payments until the Contractor has taken appropriate remedial action;
(4) Loss of award fee, consistent with the award fee plan, for the performance period in which the Government
determined Contractor non-compliance;
(5) Declining to exercise available options under the contract;
(6) Termination of the contract for default or cause, in accordance with the termination clause of this contract; or
(7) Suspension or debarment.
(f) Mitigating and aggravating factors. When determining remedies, the Contracting Officer may consider the
following:
(1) Mitigating factors. The Contractor had a Trafficking in Persons compliance plan or an awareness program at the
time of the violation, was in compliance with the plan, and has taken appropriate remedial actions for the violation,
that may include reparation to victims for such violations.
(2) Aggravating factors. The Contractor failed to abate an alleged violation or enforce the requirements of a
compliance plan, when directed by the Contracting Officer to do so.
(g) Full cooperation. (1) The Contractor shall, at a minimum--
(i) Disclose to the agency Inspector General information sufficient to identify the nature and extent of an offense and
the individuals responsible for the conduct;
(ii) Provide timely and complete responses to Government auditors' and investigators' requests for documents;
(iii) Cooperate fully in providing reasonable access to its facilities and staff (both inside and outside the U.S.) to
allow contracting agencies and other responsible Federal agencies to conduct audits, investigations, or other actions
to ascertain compliance with the Trafficking Victims Protection Act of 2000 (22
W912KN-17-T-0034
Page 15 of 24
U.S.C. chapter 78), E.O. 13627, or any other applicable law or regulation establishing restrictions on trafficking in
persons, the procurement of commercial sex acts, or the use of forced labor; and
(iv) Protect all employees suspected of being victims of or witnesses to prohibited activities, prior to returning to the
country from which the employee was recruited, and shall not prevent
or hinder the ability of these employees from cooperating fully with Government authorities.
(2) The requirement for full cooperation does not foreclose any Contractor rights arising in law, the FAR, or the
terms of the contract. It does not--
(i) Require the Contractor to waive its attorney-client privilege or the protections afforded by the attorney work
product doctrine;
(ii) Require any officer, director, owner, employee, or agent of the Contractor, including a sole proprietor, to waive
his or her attorney client privilege or Fifth Amendment rights; or
(iii) Restrict the Contractor from--
(A) Conducting an internal investigation; or
(B) Defending a proceeding or dispute arising under the contract or related to a potential or disclosed violation.
(h) Compliance plan. (1) This paragraph (h) applies to any portion of the contract that--
(i) Is for supplies, other than commercially available off-the-shelf items, acquired outside the United States, or
services to be performed outside the United States; and
(ii) Has an estimated value that exceeds $500,000.
(2) The Contractor shall maintain a compliance plan during the performance of the contract that is appropriate--
(i) To the size and complexity of the contract; and
(ii) To the nature and scope of the activities to be performed for the Government, including the number of non-
United States citizens expected to be employed and the risk that the contract or subcontract will involve services or
supplies susceptible to trafficking in persons.
(3) Minimum requirements. The compliance plan must include, at a minimum, the following:
(i) An awareness program to inform contractor employees about the Government's policy prohibiting traffickingrelated
activities described in paragraph (b) of this clause, the activities prohibited, and the actions that will be taken
against the employee for violations. Additional information about Trafficking in Persons and examples of awareness
programs can be found at the Web site for the Department of State's Office to Monitor and Combat Trafficking in
Persons at http://www.state.gov/j/tip/.
(ii) A process for employees to report, without fear of retaliation, activity inconsistent with the policy prohibiting
trafficking in persons, including a means to make available to all employees the hotline phone number of the Global
Human Trafficking Hotline at 1-844-888-FREE and its email address at [email protected].
(iii) A recruitment and wage plan that only permits the use of recruitment companies with trained employees,
prohibits charging recruitment fees to the employee, and ensures that wages meet
applicable host-country legal requirements or explains any variance.
(iv) A housing plan, if the Contractor or subcontractor intends to provide or arrange housing, that ensures that the
housing meets host-country housing and safety standards.
W912KN-17-T-0034
Page 16 of 24
(v) Procedures to prevent agents and subcontractors at any tier
and at any dollar value from engaging in trafficking in persons
(including activities in paragraph (b) of this clause) and to
monitor, detect, and terminate any agents, subcontracts, or
subcontractor employees that have engaged in such activities.
(4) Posting. (i) The Contractor shall post the relevant contents
of the compliance plan, no later than the initiation of contract
performance, at the workplace (unless the work is to be performed in
the field or not in a fixed location) and on the Contractor's Web
site (if one is maintained). If posting at
the workplace or on the Web site is impracticable, the Contractor
shall provide the relevant contents of the compliance plan to each
worker in writing.
(ii) The Contractor shall provide the compliance plan to the Contracting Officer upon request.
(5) Certification. Annually after receiving an award, the Contractor shall submit a certification to the Contracting
Officer that--
(i) It has implemented a compliance plan to prevent any prohibited activities identified at paragraph (b) of this
clause and to monitor, detect, and terminate any agent, subcontract or subcontractor employee engaging in
prohibited activities; and
(ii) After having conducted due diligence, either--
(A) To the best of the Contractor's knowledge and belief, neither it nor any of its agents, subcontractors, or their
agents is engaged in any such activities; or
(B) If abuses relating to any of the prohibited activities identified in paragraph (b) of this clause have been found,
the Contractor or subcontractor has taken the appropriate remedial and referral actions.
(i) Subcontracts. (1) The Contractor shall include the substance of this clause, including this paragraph (i), in all
subcontracts and in all contracts with agents. The requirements in paragraph (h)
of this clause apply only to any portion of the subcontract that--
(A) Is for supplies, other than commercially available off-the-shelf items, acquired outside the United States, or
services to be performed outside the United States; and
(B) Has an estimated value that exceeds $500,000.
(2) If any subcontractor is required by this clause to submit a certification, the Contractor shall require submission
prior to the award of the subcontract and annually thereafter. The certification
shall cover the items in paragraph (h)(5) of this clause.
(End of clause)
252.211-7003 ITEM UNIQUE IDENTIFICATION AND VALUATION (MAR 2016)
(a) Definitions. As used in this clauseW912KN-
17-T-0034
Page 17 of 24
Automatic identification device means a device, such as a reader or interrogator, used to retrieve data encoded on
machine-readable media.
Concatenated unique item identifier means--
(1) For items that are serialized within the enterprise identifier, the linking together of the unique identifier data
elements in order of the issuing agency code, enterprise identifier, and unique serial number within the enterprise
identifier; or
(2) For items that are serialized within the original part, lot, or batch number, the linking together of the unique
identifier data elements in order of the issuing agency code; enterprise identifier; original part, lot, or batch number;
and serial number within the original part, lot, or batch number.
Data Matrix means a two-dimensional matrix symbology, which is made up of square or, in some cases, round
modules arranged within a perimeter finder pattern and uses the Error Checking and Correction 200
(ECC200) specification found within International Standards Organization (ISO)/International Electrotechnical
Commission (IEC) 16022.
Data qualifier means a specified character (or string of characters) that immediately precedes a data field that defines
the general category or intended use of the data that follows.
DoD recognized unique identification equivalent means a unique identification method that is in commercial use and
has been recognized by DoD. All DoD recognized unique identification equivalents are listed at
http://www.acq.osd.mil/dpap/pdi/uid/iuid_equivalents.html.
DoD item unique identification means a system of marking items delivered to DoD with unique item identifiers that
have machine-readable data elements to distinguish an item from all other like and unlike items. For items that are
serialized within the enterprise identifier, the unique item identifier shall include the data elements of the enterprise
identifier and a unique serial number. For items that are serialized within the part, lot, or batch number within the
enterprise identifier, the unique item identifier shall include the data elements of the enterprise identifier; the original
part, lot, or batch number; and the serial number.
Enterprise means the entity (e.g., a manufacturer or vendor) responsible for assigning unique item identifiers to
items.
Enterprise identifier means a code that is uniquely assigned to an enterprise by an issuing agency.
Government's unit acquisition cost means--
(1) For fixed-price type line, subline, or exhibit line items, the unit price identified in the contract at the time of
delivery;
(2) For cost-type or undefinitized line, subline, or exhibit line items, the Contractor's estimated fully burdened unit
cost to the Government at the time of delivery; and
(3) For items produced under a time-and-materials contract, the Contractor's estimated fully burdened unit cost to
the Government at the time of delivery.
Issuing agency means an organization responsible for assigning a globally unique identifier to an enterprise, as
indicated in the Register of Issuing Agency Codes for ISO/IEC 15459, located at
http://www.aimglobal.org/?Reg_Authority15459.
Issuing agency code means a code that designates the registration (or controlling) authority for the enterprise
identifier.
W912KN-17-T-0034
Page 18 of 24
Item means a single hardware article or a single unit formed by a grouping of subassemblies, components, or
constituent parts.
Lot or batch number means an identifying number assigned by the enterprise to a designated group of items, usually
referred to as either a lot or a batch, all of which were manufactured under identical conditions.
Machine-readable means an automatic identification technology media, such as bar codes, contact memory buttons,
radio frequency identification, or optical memory cards.
Original part number means a combination of numbers or letters assigned by the enterprise at item creation to a class
of items with the same form, fit, function, and interface.
Parent item means the item assembly, intermediate component, or subassembly that has an embedded item with a
unique item identifier or DoD recognized unique identification equivalent.
Serial number within the enterprise identifier means a combination of numbers, letters, or symbols assigned by the
enterprise to an item that provides for the differentiation of that item from any other like and unlike item and is
never used again within the enterprise.
Serial number within the part, lot, or batch number means a combination of numbers or letters assigned by the
enterprise to an item that provides for the differentiation of that item from any other like item within a part, lot, or
batch number assignment.
Serialization within the enterprise identifier means each item produced is assigned a serial number that is unique
among all the tangible items produced by the enterprise and is never used again. The enterprise is responsible for
ensuring unique serialization within the enterprise identifier.
Serialization within the part, lot, or batch number means each item of a particular part, lot, or batch number is
assigned a unique serial number within that part, lot, or batch number assignment. The enterprise is responsible for
ensuring unique serialization within the part, lot, or batch number within the enterprise identifier.
Type designation means a combination of letters and numerals assigned by the Government to a major end item,
assembly or subassembly, as appropriate, to provide a convenient means of differentiating between items having the
same basic name and to indicate modifications and changes thereto.
Unique item identifier means a set of data elements marked on items that is globally unique and unambiguous. The
term includes a concatenated unique item identifier or a DoD recognized unique identification equivalent.
Unique item identifier type means a designator to indicate which method of uniquely identifying a part has been
used. The current list of accepted unique item identifier types is maintained at
http://www.acq.osd.mil/dpap/pdi/uid/uii_types.html.
(b) The Contractor shall deliver all items under a contract line, subline, or exhibit line item.
(c) Unique item identifier. (1) The Contractor shall provide a unique item identifier for the following:
(i) Delivered items for which the Government's unit acquisition cost is $5,000 or more, except for the following line
items:
------------------------------------------------------------------------
Contract line, subline, or exhibit
line item No. Item description
------------------------------------------------------------------------
001 Gazebo
W912KN-17-T-0034
Page 19 of 24
...................................
------------------------------------------------------------------------
(ii) Items for which the Government's unit acquisition cost is less than $5,000 that are identified in the Schedule or
the following table:
------------------------------------------------------------------------
Contract line, subline, or exhibit
line item No. Item description
------------------------------------------------------------------------
...................................
------------------------------------------------------------------------
(If items are identified in the Schedule, insert ``See Schedule'' in this table.)
(iii) Subassemblies, components, and parts embedded within delivered items, items with warranty requirements,
DoD serially managed reparables and DoD serially managed nonreparables as specified in Attachment Number ----.
(iv) Any item of special tooling or special test equipment as defined in FAR 2.101 that have been designated for
preservation and storage for a Major Defense Acquisition Program as specified in Attachment Number ----.
(v) Any item not included in paragraphs (c)(1)(i), (ii), (iii), or
(iv) of this clause for which the contractor creates and marks a unique item identifier for traceability.
(2) The unique item identifier assignment and its component data element combination shall not be duplicated on
any other item marked or registered in the DoD Item Unique Identification Registry by the contractor.
(3) The unique item identifier component data elements shall be marked on an item using two dimensional data
matrix symbology that complies with ISO/IEC International Standard 16022, Information
technology--International symbology specification--Data matrix; ECC200 data matrix specification.
(4) Data syntax and semantics of unique item identifiers. The Contractor shall ensure that--
(i) The data elements (except issuing agency code) of the unique item identifier are encoded within the data matrix
symbol that is marked on the item using one of the following three types of data qualifiers, as determined by the
Contractor:
(A) Application Identifiers (AIs) (Format Indicator 05 of ISO/IEC International Standard 15434), in accordance with
ISO/IEC International Standard 15418, Information Technology--EAN/UCC Application Identifiers and Fact Data
Identifiers and Maintenance and ANSI MH 10.8.2 Data Identifier and Application Identifier Standard.
(B) Data Identifiers (DIs) (Format Indicator 06 of ISO/IEC International Standard 15434), in accordance with
ISO/IEC International Standard 15418, Information Technology--EAN/UCC Application Identifiers
and Fact Data Identifiers and Maintenance and ANSI MH 10.8.2 Data Identifier and Application Identifier Standard.
(C) Text Element Identifiers (TEIs) (Format Indicator 12 of ISO/IEC International Standard 15434), in accordance
with the Air Transport Association Common Support Data Dictionary; and
(ii) The encoded data elements of the unique item identifier conform to the transfer structure, syntax, and coding of
messages and data formats specified for Format Indicators 05, 06, and 12 in ISO/IEC International Standard 15434,
Information Technology-Transfer Syntax for High Capacity Automatic Data Capture Media.
(5) Unique item identifier.
W912KN-17-T-0034
Page 20 of 24
(i) The Contractor shall--
(A) Determine whether to--
(1) Serialize within the enterprise identifier;
(2) Serialize within the part, lot, or batch number; or
(3) Use a DoD recognized unique identification equivalent (e.g. Vehicle Identification Number); and
(B) Place the data elements of the unique item identifier (enterprise identifier; serial number; DoD recognized
unique
identification equivalent; and for serialization within the part, lot, or batch number only: Original part, lot, or batch
number) on items requiring marking by paragraph (c)(1) of this clause, based on the criteria provided in MIL-STD-
130, Identification Marking of U.S. Military Property, latest version;
(C) Label shipments, storage containers and packages that contain uniquely identified items in accordance with the
requirements of MIL-STD-129, Military Marking for Shipment and Storage, latest version; and
(D) Verify that the marks on items and labels on shipments, storage containers, and packages are machine readable
and conform to the applicable standards. The contractor shall use an automatic identification technology device for
this verification that has been programmed to the requirements of Appendix A, MIL-STD-130, latest
version.
(ii) The issuing agency code--
(A) Shall not be placed on the item; and
(B) Shall be derived from the data qualifier for the enterprise identifier.
(d) For each item that requires item unique identification under paragraph (c)(1)(i), (ii), or (iv) of this clause or when
item unique identification is provided under paragraph (c)(1)(v), in addition to the information provided as part of
the Material Inspection and Receiving Report specified elsewhere in this contract, the Contractor shall report at the
time of delivery, as part of the Material Inspection and Receiving Report, the following information:
(1) Unique item identifier.
(2) Unique item identifier type.
(3) Issuing agency code (if concatenated unique item identifier is used).
(4) Enterprise identifier (if concatenated unique item identifier is used).
(5) Original part number (if there is serialization within the original part number).
(6) Lot or batch number (if there is serialization within the lot or batch number).
(7) Current part number (optional and only if not the same as the original part number).
(8) Current part number effective date (optional and only if current part number is used).
(9) Serial number (if concatenated unique item identifier is used).
(10) Government's unit acquisition cost.
W912KN-17-T-0034
Page 21 of 24
(11) Unit of measure.
(12) Type designation of the item as specified in the contract schedule, if any.
(13) Whether the item is an item of Special Tooling or Special Test Equipment.
(14) Whether the item is covered by a warranty.
(e) For embedded subassemblies, components, and parts that require DoD unique item identification under
paragraph (c)(1)(iii) of this clause, the Contractor shall report as part of, or associated with, the Material Inspection
and Receiving Report specified elsewhere in this contract, the following information:
(1) Unique item identifier of the parent item under paragraph (c)(1) of this clause that contains the embedded
subassembly, component, or part.
(2) Unique item identifier of the embedded subassembly, component, or part.
(3) Unique item identifier type.**
(4) Issuing agency code (if concatenated unique item identifier is used).**
(5) Enterprise identifier (if concatenated unique item identifier is used).**
(6) Original part number (if there is serialization within the original part number).**
(7) Lot or batch number (if there is serialization within the lot or batch number).**
(8) Current part number (optional and only if not the same as the original part number).**
(9) Current part number effective date (optional and only if current part number is used).**
(10) Serial number (if concatenated unique item identifier is used).**
(11) Description.
** Once per item.
(f) The Contractor shall submit the information required by paragraphs (d) and (e) of this clause as follows:
(1) End items shall be reported using the receiving report capability in Wide Area WorkFlow (WAWF) in
accordance with the clause at 252.232-7003. If WAWF is not required by this contract, and the
contractor is not using WAWF, follow the procedures at http://dodprocurementtoolbox.com/site/uidregistry/.
(2) Embedded items shall be reported by one of the following methods--
(i) Use of the embedded items capability in WAWF;
(ii) Direct data submission to the IUID Registry following the procedures and formats at
http://dodprocurementtoolbox.com/site/uidregistry/; or
(iii) Via WAWF as a deliverable attachment for exhibit line item number (fill in) ----, Unique Item Identifier Report
for Embedded Items, Contract Data Requirements List, DD Form 1423.
W912KN-17-T-0034
Page 22 of 24
(g) Subcontracts. If the Contractor acquires by subcontract any items for which item unique identification is required
in accordance with paragraph (c)(1) of this clause, the Contractor shall include this clause, including this paragraph
(g), in the applicable subcontract(s), including subcontracts for commercial items.
(End of clause)
252.232-7006 WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (MAY 2013)
(a) Definitions. As used in this clause--
Department of Defense Activity Address Code (DoDAAC) is a six position code that uniquely identifies a unit,
activity, or organization.
Document type means the type of payment request or receiving report available for creation in Wide Area
WorkFlow (WAWF).
Local processing office (LPO) is the office responsible for payment certification when payment certification is done
external to the entitlement system.
(b) Electronic invoicing. The WAWF system is the method to electronically process vendor payment requests and
receiving reports, as authorized by DFARS 252.232-7003, Electronic Submission
of Payment Requests and Receiving Reports.
(c) WAWF access. To access WAWF, the Contractor shall--
(1) Have a designated electronic business point of contact in the System for Award Management at
https://www.acquisition.gov; and
(2) Be registered to use WAWF at https://wawf.eb.mil/ following the step-by-step procedures for self-registration
available at this Web site.
(d) WAWF training. The Contractor should follow the training instructions of the WAWF Web-Based Training
Course and use the Practice Training Site before submitting payment requests through
WAWF. Both can be accessed by selecting the "Web Based Training" link on the WAWF home page at
https://wawf.eb.mil/.
(e) WAWF methods of document submission. Document submissions may be via Web entry, Electronic Data
Interchange, or File Transfer Protocol.
(f) WAWF payment instructions. The Contractor must use the following information when submitting payment
requests and receiving reports in WAWF for this contract/order:
(1) Document type. The Contractor shall use the following document type(s).
COMBO (2-IN-1)
(Contracting Officer: Insert applicable document type(s). Note: If a "Combo" document type is identified but not
supportable by the Contractor's business systems, an "Invoice" (stand-alone) and
"Receiving Report" (stand-alone) document type may be used instead.)
(2) Inspection/acceptance location. The Contractor shall select the following inspection/acceptance location(s) in
WAWF, as specified by the contracting officer.
W912KN-17-T-0034
Page 23 of 24
F6B2MG
(Contracting Officer: Insert inspection and acceptance locations or "Not applicable".)
(3) Document routing. The Contractor shall use the information in the Routing Data Table below only to fill in
applicable fields in WAWF when creating payment requests and receiving reports in the
system.
Routing Data Table*
--------------------------------------------------------------------------------------------
Field Name in WAWF Data to be entered in WAWF
--------------------------------------------------------------------------------------------
Pay Official DoDAAC F67100
Issue By DoDAAC W912KN
Admin DoDAAC W912KN
Inspect By DoDAAC F6B2MG
Ship To Code F6B2MG
Ship From Code ____
Mark For Code ____
Service Approver (DoDAAC) ____
Service Acceptor (DoDAAC) ____
Accept at Other DoDAAC ____
LPO DoDAAC ____
DCAA Auditor DoDAAC ____
Other DoDAAC(s) ____
--------------------------------------------------------------------------------------------
(*Contracting Officer: Insert applicable DoDAAC information or "See schedule" if multiple ship to/acceptance
locations apply, or "Not applicable.")
(*WAWF may automatically pre-fill some or most of the data provided in the routing table)
(4) Payment request and supporting documentation. The Contractor shall ensure a payment request includes
appropriate contract line item and subline item descriptions of the work performed or supplies delivered, unit
price/cost per unit, fee (if applicable), and all relevant back-up documentation, as defined in DFARS Appendix F,
(e.g. timesheets) in support of each payment request.
(5) WAWF email notifications. The Contractor shall enter the email address identified below in the "Send
Additional Email Notifications" field of WAWF once a document is submitted in the system.
SMSgt Jim Miller; [email protected] 609-761-6015
(Contracting Officer: Insert applicable email addresses or "Not applicable.")
(g) WAWF point of contact. (1) The Contractor may obtain clarification regarding invoicing in WAWF from the
following contracting activity's WAWF point of contact.
MSgt Tammy Hickerson: [email protected]; 609-761-6522
Ms Johanna Paz: [email protected]; 609-761-6097
(Contracting Officer: Insert applicable information or "Not applicable.")
(2) For technical WAWF help, contact the WAWF helpdesk at 866-618-5988.
(End of clause)

Bid Protests Not Available