COLLET HEAD,ASSEMBL

82N ALRE CSI
P/N 7-1668-3

The following Supplemental Quality Assurance Provisions apply:

SQAP014889284QA

The following DD Form 1423 CDRL's apply:

CDRL-13-12019-TI
CDRL-13-12019-MP
CDRL-13-12019-MRB

PCO MANDATORY INSPECTION. DURING PRODUCTION,
MANDATORY INSPECTION IS REQUIRED TO BE
ACCOMPLISHED AND DOCUMENTED BY THE CONTRACTOR AS
FOLLOWS:
.
CRITICAL AND MAJOR CHARACTERISTICS AS IDENTIFIED
IN CLASSIFICATION OF CHARACTERISTICS BLOCK ON
DRAWING(S), TECHNICAL SPECIFICATIONS, SECOND
TIER DOCUMENTS REFERENCED IN THE ACQUISITION
ITEM DESCRIPTION AND SPECIFIED IN THE
PROCUREMENT DOCUMENT, AND CHARACTERISTICS
DEFINED AS:
(A) MATERIAL CERTIFICATIONS
(B) DESTRUCTIVE AND / OR NONDESTRUCTIVE
TEST RESULTS (WHEN APPLICABLE)
(C) ATTRIBUTES FOR PLATING HARDNESS
.
IMPORTANT MINOR CHARACTERISTICS SHALL BE
DEFINED BY THE CONTRACTOR SUBJECT TO QAR
CONCURRENCE, UNLESS OTHERWISE DEFINED ON
APPLICABLE DRAWING(S), SPECIFICATIONS
AND CHARRACTERISTICS DEFINED AS:
(A) DIAMETRICAL AND LINEAR DIMENSIONS
HAVING A TOLERANCE OF +/- 0.005 INCH OR
LESS
(B) GEOMETRIC FEATURE CONTROLS HAVING A TOTAL
TOLERANCE OF 0.003 INCH OR LESS
(C) SURFACE FINISHES HAVING A 16 VALUE OR LESS
(D) CLASS THREE THREADS
(E) ANGULAR TOLERANCES WITH A TOTAL RANGE LESS
THAN 1 DEGREE
.
LEVEL OF INSPECTION: ANSI / ASQC Z1.4 FOR SINGLE
SAMPLING USING A GENERAL INSPECTION LEVEL O II
(A) CRITICAL AND MAJOR CHARACTERISTICS: 100%
INSPECTION APPLIES
(B) IMPORTANT MINOR CHARACTERISTICS: AQL OF 1.5
.
CERTIFICATION / DATA REPORTS: THE CONTRACTOR IS
RESPONSIBLE FOR PREPARING A CERTIFICATE OF
QUALITY COMPLIANCE (COQC) IN ACCORDANCE WITH THE
DD FORM 1423 CONTRACT DATA REQUIREMENTS LIST
(CDRL). THE COQC CONTENT WILL INCLUDE AS A
MINIMUM THE DATA DESCRIBED IN DLAR CLAUSE
52.246-9000, IN ADDITION TO ALL PCO MANDATORY
INSPECTION RESULTS. THIS COQC REQUIREMENT
APPLIES TO EACH UNIT OF CONTRACT QUANTITY.

CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE
USED NOR INCORPORATED IN ANY ITEMS TO BE
DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION
SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT
DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.
SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR
APPROVAL UNLESS THEY ARE AUTHORIZED BY THE
SPECIFICATION REQUIREMENTS.

MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL
NOT BE INTENTIONALLY ADDED TO,OR COME IN DIRECT
CONTACT WITH,ANY HARDWARE OR SUPPLIES FURNISHED
UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY
USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED
INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;
AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.
PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS
CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN
A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR
MERCURY COMPOUND. (IAW NAVSEA 5100-003D).

NO DATA IS AVAILABLE.  THE ALTERNATE OFFEROR IS
REQUIRED TO PROVIDE A COMPLETE DATA PACKAGE
INCLUDING DATA FOR THE APPROVED AND ALTERNATE
PART FOR EVALUATION.

"CERTIFICATE OF QUALITY COMPLIANCE IS MANDATORY"

FAR CLAUSE 52.246-11 APPLIES

A QUALITY MANAGEMENT PROGRAM MEETING THE REQUIREMENTS OF ISO 9001:2008
OR THE FOLLOWING TAILORED VERSION OF ISO 9001:2008 IS REQUIRED OR A
PROGRAM EQUIVALENT TO THE TAILORED VERSION OF THE ISO 9001:2008 IS
REQUIRED.

DLA TAILORED HIGHER LEVEL QUALITY CLAUSE FROM ISO 9001:2008

4.2.1   General, Documentation Requirements [b and d only]
4.2.2   Quality manual
4.2.3   Control of documents
4.2.4   Control of records
6.2.2   Competence, training and awareness
6.4     Work environment (if applicable)
7.1     Planning of product realization
7.2.1   Determination of requirements related to the product
7.2.2   Review of the requirements related to product
7.2.3   Customer communication
7.3.7   Control of design and development changes
7.4.1   Purchase Product
7.4.3   Verification of purchased product
7.5.1   Control of production and service provision
7.5.3   Identification and traceability
7.5.4   Customer property (if applicable)
7.5.5   Preservation of product
7.6     Control of monitoring and measuring equipment
8.1a,,General for Measurement, Analysis and Improvement
8.2.2   Internal Audit
8.3     Control of nonconforming product
8.2.4   Monitoring and measurement of product
8.5.2   Corrective action
8.5.3   Preventive action

AIRCRAFT LAUNCH AND RECOVERY EQUIPMENT (ALRE)
.
CRITICAL APPLICATION ITEM.
.
ALL REQUESTS FOR WAIVERS OR DEVIATIONS
CLASSIFIED AS CRITICAL, MAJOR, OR MINOR MUST BE
FORWARDED TO THE DSC CONTRACTING OFFICER FOR
REVIEW AND APPROVAL.
.
ALL ITEMS OF SUPPLY SHALL BE MARKED IAW
MIL-STD-129.  IN ADDITION, EACH UNIT PACK WILL
BE MARKED WITH LOT AND SERIAL NUMBER (IF AVAILABLE),
CONTRACTOR'S CAGE CODE, ACTUAL MANUFACTURER'S
CAGE CODE AND PART NUMBER.
EACH UNIT PACKAGE WILL BE MARKED WITH THE NSN,
CONTRACT NUMBER, LOT NUMBER, CONTRACTOR CAGE
CODE, MANUFACTURER CAGE CODE, AND PART NUMBER.

ITEM IS EXPORT CONTROLLED. SPECIAL MARKINGS CODE 40
APPLIES.

GE AVIATION SYSTEMS LLC 97415 P/N 7-1668-3

IAW REFERENCE QAP 16236 SQAP014889284
REVISION NR     DTD 06/17/2013
PART PIECE NUMBER:

IAW REFERENCE QAP 97415 CDRL-13-12019-TI
REVISION NR     DTD 04/29/2013
PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 16236 CN014889284
REVISION NR E   DTD 06/14/2013
PART PIECE NUMBER:

IAW REFERENCE QAP 97415 CDRL-13-12019-MP
REVISION NR     DTD 04/29/2013
PART PIECE NUMBER:

IAW REFERENCE QAP 97415 CDRL-13-12019-MRB
REVISION NR     DTD 04/29/2013
PART PIECE NUMBER: