Point Of Contact Not Available

CITY OF AMORY MISSISSIPPI – ELECTRIC DEPARTMENT One Man Bucket Truck Bid specifications as atttachment for easy printing. Please fill out sheet. This device shall be to the manufacture's standard. It shall be equipped with the manufacture's equipment and accessories which are included as standard in the advertised and published literature for the unit. No such item of equipment or accessories shall be removed or omitted for the reason that it was not specified in the bid. If it is necessary to bid alternate equipment or to take exceptions to the specifications as set forth, this must be so stated in your bid. For each item, please place a X in the appropriate space (Yes__ No__) to signify whether or not you are in complete compliance with the specification. Failure to follow the format or answer the specification may cause your bid to be disqualified. If you need extra space to describe your product, please attach extra sheets. When doing this, be sure your description references the appropriate question number. General Specifications Comply Item Description Units Qty Yes No Unit 1. Articulating Telescopic Aerial Device with a fiberglass upper boom and fiberglass insulator in the articulating arm and proportional joystick upper controls. Built in accordance to below standard specifications and to include the following features: EA 1 ____ ____ A. Ground to Bottom of Platform Height: 47.5 feet at 6.7 feet from centerline of rotation (14.48 m at 2.04 m) ____ ____ B. Working Height: 52.5 feet (16.00 m) ____ ____ C. Maximum reach to edge of platform with Upper Boom Non- overcenter: 31.2 feet (at 21.9 feet platform height) ____ ____ D. Upper boom extension: 110 inches ____ ____ E. Continuous rotation ____ ____ F. Articulating Arm: Articulation is from -3 to 82 degrees. Insulator provides 19 inches of isolation. ____ ____ G. Compensation System: By raising the articulating arm only, the telescopic boom maintains its relative angle in relation to the ground. The work position is achieved through a single function operation. ____ ____ H. Upper Boom: Articulation is from -25 to 85 degrees. The fiberglass section provides a minimum of 33.1 inches of isolation in the upper boom (when retracted and 64.6 inches when extended) ____ ____ I. Platform leveling is achieved by a hydraulic master-slave leveling system. This lifetime system is very low maintenance. ____ ____ J. The dielectrically tested, insulating upper control system includes the following boom tip components that can provide an additional layer of secondary electrical contact protection. Control Handle: A single handle controller incorporating high electrical resistance components that is dielectrically tested to 40 kV AC with no more than 400 microampers of leakage. The control handle is different in color to differentiate it from other non-tested controllers. The handle also includes an interlock guard that reduces the potential for inadvertent boom operation. Auxiliary Control Covers: Non-tested colored silicon covers for auxiliary controls. Control Console: Non-tested non-metallic control console plate. Boom Tip Covers: Non-tested non-metallic boom tip covers. The covers are not dielectrically tested, but they may provide some protection against electrical hazards. ____ ____ K. Hydraulic system: Open center (full pressure), maximum flow 6 GPM, maximum operating pressure 3,000. ____ ____ L. Dielectric rating: Category C, 46 kV and below ____ ____ M. Unit is painted with a powder coat paint process which provides a finish-painted surface that is highly resistant to chipping, scratching, abrasion and corrosion. Paint is electrostatically applied to the inside as well as outside of fabricated parts then high temperature cured prior to assembly ensuring maximum coverage and protection. ____ ____ N. Manuals: Two (2) Operator’s and two (2) Maintenance/ Parts manuals containing instructional markings indicating hazards inherent in the operation of an aerial device. ____ ____ O. Unit meets or exceeds ANSI 92.2 standards. ____ ____ 2. Pedestal EA 1 ____ ____ 3. Single 1-Man Platform, Fiberglass, 24" x 30" x 42", End Mount, 180 Degree Rotation EA 1 ____ ____ 4. Platform Mounted Single Handle Controls EA 1 ____ ____ 5. Material Handling Jib/Winch, Hydraulically Articulating, Top Mounted, Round (ARM Jib) EA 1 ____ ____ 6. One (1) Platform Step - located on the side of the platform nearest the elbow in the stowed position EA 1 ____ ____ 7. Platform Cover - soft vinyl, 24 x 30 inches (610 x 762 mm) EA 1 ____ ____ 8. Platform Liner, 24 x 30 x 42 inches (610 x 762 x 1067 mm), 50 kV Rating EA 1 ____ ____ 9. Hydraulic Tool Circuit at Platform: One set of quick disconnect couplings at the boom tip for open center tools. EA 1 ____ ____ 10. Engine Start/Stop & Secondary Stowage System: 12 VDC powered motor and pump assembly for temporary operation of the unit in a situation wherein the primary hydraulic source fails. Electric motor is powered by the chassis battery. This feature allows the operator to completely stow the booms, platform, and outriggers. Secondary Stowage & Start/Stop is activated with an air plunger at the platform or momentary switch at the lower control station and outriggers. EA 1 ____ ____ 11. Jib Stick, 36" L, Non-Extension Dependent, Non-Certified EA 1 ____ ____ 12. Slip Ring: Required for engine start/stop, secondary stowage system, and throttle control options EA 1 ____ ____ 13. Outriggers, Primary, Modified A-Frame, 30"-34" Chassis Height, Electric Interlock, No Valves On Legs, 112" Spread, Fixed Shoe EA 1 ____ ____ 14. Auxiliary Vertical H Frame Outriggers with fixed shoe. EA 1 ____ ____ A. Maximum Spread: 87 inches to the outer edge of shoes ____ ____ B. Outrigger Motion Alarms ____ ____ C. Outrigger Interlocks: will not allow the unit to be operated until the outriggers have been at least partially deployed ____ ____ 15. Winch load line swivel hook EA 1 ____ ____ 16. Powder Painted White EA 1 ____ ____ Unit & Hydraulic Acc. 17. Scuff Pad, 24" x 30", No Step (For use with Platform Liner) EA 1 ____ ____ 18. Subbase EA 1 ____ ____ 19. Electric Outrigger Controls for two (2) sets of outriggers, drive hydraulic outrigger control valves. Durable weather proof sealed electronic switches mounted in the aluminum boxes are located at the rear of the unit. Use of electronic sealed switches reduces the number of hydraulic hoses and leak points. EA 1 ____ ____ 20. Steel Reservoir, 15 gallon capacity, rectangular, 26" L x 8.5" W x 20" H, and includes breather caps and dipsticks EA 1 ____ ____ 21. Temperature Sight Gauge EA 1 ____ ____ 22. HVI-22 Hydraulic Oil (Standard). EA 25 ____ ____ 23. Standard Pump For PTO EA 1 ____ ____ 24. Electric Shifted PTO EA 1 ____ ____ 25. Standard PTO/Transmission Functionality for class 5 Chassis EA 1 ____ ____ Body 26. Low-Side General Service Body With Step: EA 1 ____ ____ A. Steel Body ____ ____ B. Steel Structural Channel Crossmembers And Smooth Floor With Ladder-Style Understructure ____ ____ C. 132'' Body Length ____ ____ D. 94'' Body Width ____ ____ E. 40'' Body Compartment Height ____ ____ F. 20'' Body Compartment Depth ____ ____ G. 24'' From Body Floor To Compartment Tops ____ ____ H. Finish Paint Entire Body White ____ ____ I. Undercoat Applied Under The Body ____ ____ J. 5.5'' Drop-In Composite Cargo Retaining Board At Rear Of Body ____ ____ K. 5.5'' Drop-In Composite Retaining Board At Top Of Side Access Step ____ ____ L. Stainless Steel Rotary paddle Latches With Locks ____ ____ M. Gas Props On All Vertical Doors ____ ____ N. Chains On All Horizontal Doors ____ ____ O. Standard Master Body Locking System ____ ____ P. Hotstick Shelf Extending Full Length Of Body On Streetside ____ ____ Q. Two (2) hotstick brackets installed on street side. ____ ____ R. One Chock Holder On Each Side of Body With Retaining Lip In Fender Panel ____ ____ S. 1st Vertical (SS) - 34'' W - One (1) Outrigger Housing And Two (2) Adjustable Shelves With Removable Dividers On 4 Inch Centers ____ ____ T. 2nd Vertical (SS) - 24'' W - Two (2) Adjustable Shelves With Removable Dividers On 4 Inch Centers ____ ____ U. 1st Horizontal (SS) - 50'' W - One (1) Fixed Shelf With Removable Dividers On 4 Inch Centers On Bottom of Compartment ____ ____ V. Rear Vertical (SS) - 24'' W - Six (6) Locking Swivel Hooks On An Adjustable Rail (1-4-1) ____ ____ W. 1st Vertical (CS) - 34'' W - One (1) Outrigger Housing And Two (2) Adjustable Shelves With Removable Dividers On 4 Inch Centers ____ ____ X. 2nd Vertical (CS) - 24'' W - Gripstrut Access Steps With Two (2) Sloped Grab Handles, Vented Battery Storage ____ ____ Y. 1st Horizontal (CS) - 50'' W - One (1) Adjustable Shelf With Removable Dividers On 4 Inch Centers And One (1) Fixed Shelf With Removable Dividers On 4 Inch Centers On Bottom Of Compartment ____ ____ Z. Rear Vertical (CS) - 24'' W - Six (6) Locking Swivel Hooks On An Adjustable Rail (1-4-1) ____ ____ ZA. Body Floor Cut-Out For Aerial Device Near Center Of Body ____ ____ ZB. Steel Tailshelf, 29'' L x 94'' W, With Rear Cross Storage And Drop Down Doors ____ ____ Body and Chassis Accessories 27. ICC (Underride Protection) Bumper Installed At Rear EA 1 ____ ____ 28. Combination 2 Ball (10 000 LB MGTW) and Rigid Pintle Hitch (16 000 LB MGTW with 3 000 LB MVL) EA 1 ____ ____ 29. Set Of Eye Bolts for Trailer Safety Chain, installed one each side of towing device mount. EA 1 ____ ____ 30. Rigid Step Mounted Beneath Side Access Steps (Installed To Extend Approx. 2'' Outward) EA 1 ____ ____ 31. Platform Rest, Rigid with Rubber Tube EA 1 ____ ____ 32. Articulating Arm Rest for a Telescopic Unit EA 1 ____ ____ 33. Boom Rest for a Telescopic Unit EA 1 ____ ____ 34. Wood Outrigger Pad, 19'' x 19'' x 2.5'', With Rope Handle EA 4 ____ ____ 35. Outrigger Pad Holder, 20" L x 20" W x 7" H, Fits 19.5" x 19.5" And Smaller Pads, Bolt-On, Bottom Washout Holes, 3/4" Lip Retainer EA 2 ____ ____ 36. Pendulum Retainers For Outrigger Pad Holders EA 2 ____ ____ 37. Mud Flaps With Logo (Pair) EA 1 ____ ____ 38. Wheel Chocks, Rubber, 9.75'' L x 7.75'' W x 5.00'' H, with 4'' L Metal Hairpin Style Handle (Pair) EA 1 ____ ____ 39. Slope Indicator Assembly (Pair) For Machine With Outriggers EA 1 ____ ____ 40. Safety Harness & 4.5 FT Lanyard (Medium To X-large) EA 1 ____ ____ 41. Driveaway Safety Kit EA 1 ____ ____ 42. Vinyl manual pouch for storage of all operator and parts manuals EA 1 ____ ____ Electrical Accessories 43. Lights and reflectors in accordance with FMVSS #108 lighting package. (Complete LED, including LED reverse lights) EA 1 ____ ____ 44. 4-Corner Strobes, Amber, LED, Two (2) Surface Mounted Lights In Grille, Two (2) Round Lights At Rear EA 1 ____ ____ 45. Strobe Beacon, Amber LED, With Brush Guard, Installed On Post At Front Of Body, One (1) Each Side (Standard) (Federal Signal #420221-02) EA 1 ____ ____ 46. Dual Tone Back-Up With Outrigger Motion Alarm EA 1 ____ ____ 47. PTO Hour Meter, Digital, with 10,000 Hour Display EA 1 ____ ____ 48. 6-Way Trailer Receptacle (Pin Type) Installed At Rear EA 1 ____ ____ 49. Upfitter Switches (Supplied with Chassis) EA 1 ____ ____ 50. 16,500LB Electric Winch Kit to include a grill guard mount assembly with an Emergency stop switch EA 1 ____ ____ 51. Power Distribution Module Is A Compact Self-Contained Electronic System That Provides A Standardized Interface With The Chassis Electrical System. (Includes Operator's Manual) EA 1 ____ ____ 52. Install secondary stowage system. EA 1 ____ ____ 53. Install Remote Start/Stop system in Final Assembly. EA 1 ____ ____ 54. Install Outrigger Interlock System EA 1 ____ ____ 55. Heavy Duty Secondary Stowage Pump EA 1 ____ ____ 56. PTO Indicator Light Installed In Cab EA 1 ____ ____ Finishing Details 57. Powder Coat Unit Standard White EA 1 ____ ____ 58. Finish Paint Body Accessories Above Body Floor White EA 1 ____ ____ 59. Front and Rear Frame or Under Body Mounted Components To Be Painted Black EA 1 ____ ____ 60. Apply Non-Skid Coating to all walking surfaces EA 1 ____ ____ 61. English Safety And Instructional Decals EA 1 ____ ____ 62. Vehicle Height Placard - Installed In Cab EA 1 ____ ____ 63. Placard, HVI-22 Hydraulic Oil EA 1 ____ ____ 64. Dielectric test unit according to ANSI requirements. EA 1 ____ ____ 65. Stability test unit according to ANSI requirements. EA 1 ____ ____ 66. Focus Factory Build EA 1 ____ ____ 67. Delivery Of Completed Unit EA 1 ____ ____ 68. Inbound Freight EA 1 ____ ____ 69. As Built Electrical And Hydraulic Schematics To Be Included In The Manual Pouch EA 1 ____ ____ 70. Quick Turnaround EA 1 ____ ____ 71. Stock Unit EA 1 ____ ____ 72. Stock Unit Sold To Customer EA 1 ____ ____ Chassis 73. Chassis EA 1 ____ ____ 74. Chassis EA 1 ____ ____ A. 2022 or newer Model Year ____ ____ B. Class 5 chassis ____ ____ C. Regular Cab ____ ____ D. 4x4 Drivetrain ____ ____ E. Chassis Color - White ____ ____ F. 6.7L Diesel ____ ____ G. 330 HP Engine Rating ____ ____ H. 10-Speed Automatic Transmission (w/PTO Provision) ____ ____ I. Clear Cab to Axle Length - 84 inches ____ ____ J. Wheelbase Length - 169 inches ____ ____ K. 19,500 LBS Gross Vehicle Weight Rating (GVWR) ____ ____ L. 7,500 LBS Front Axle Weight Rating (FAWR) ____ ____ M. 14,706 LBS Rear Axle Weight Rating (RAWR) ____ ____ N. Single Horizontal Right Side Exhaust ____ ____ O. Hydraulic Brakes ____ ____ P. Park Brake In Rear Wheels ____ ____ Q. 40 Gallon Fuel Tank (Rear) ____ ____ R. 7.2 Gallon DEF Tank (Mid Mount) ____ ____ S. 225/70R19.5 Front Tire ____ ____ T. 225/70R19.5 Rear Tire ____ ____ U. 98R - Operator Commanded Regeneration (OCR) ____ ____ V. 63C - Aft Axle Frame Extension ____ ____ W. No Idle Engine Shut-Down Required ____ ____ X. 50-State Emissions ____ ____ Y. Clean Idle Certification ____ ____ Z. Air Conditioning ____ ____ ZA. AM/FM Radio ____ ____ ZB. Block Heater ____ ____ ZC. Bluetooth ____ ____ ZD. Cruise Control ____ ____ ZE. Keyless Entry ____ ____ ZF. Limited Slip Rear Axle ____ ____ ZG. Power Door Locks ____ ____ ZH. Power Mirrors with Heated Glass ____ ____ ZI. Power Windows ____ ____ ZJ. Tilt Steering Wheel ____ ____ ZK. Trailer Brake Controller (Factory Installed) ____ ____ ZL. Vinyl Split Bench Seat ____ ____ Additional Pricing 75. Warranty: One (1) year parts warranty, one (1) year labor warranty, ninety (90) days warranty for travel charges, limited lifetime structural warranty EA 1 ____ ____ USE OF OTHER NAMES AND REFERENCES: Unless otherwise stated, the use of manufacturer's name and product numbers are for descriptive purposes and establishing general quality levels only. They are not intended to be restrictive. Bidders are required to state exactly what they intend to furnish, otherwise, it is fully understood that they shall furnish all items stated. BROCHURES AND LITERATURE: Your proposal must be accompanied by descriptive literature (marked), indicating the exact items to be furnished. The term "as specified" will not be acceptable.

Bid Protests Not Available