TAPE CONNECTOR ASSY

82N CSI

GOVERNMENT FIRST ARTICLE TESTING APPLIES

PRE-AWARD AND POST-AWARD SURVEY APPLIES

THE FOLLOWING DD FORM 1423 CDRL'S APPLY:

CDRL 14-12025FAT
CDRL 14-12025PTI
CDRL 14 -12025COQC

THE FOLLOWING SUPPLEMENTAL QUALITY ASSURANCE PROVISIONS APPLY:

SQAP009903783QA
SQAP009903783FAT

AIRCRAFT LAUNCH AND RECOVERY EQUIPMENT (ALRE)
.
CRITICAL APPLICATION ITEM.
.
ALL REQUESTS FOR WAIVERS OR DEVIATIONS
CLASSIFIED AS CRITICAL, MAJOR, OR MINOR MUST BE
FORWARDED TO THE DSC CONTRACTING OFFICER FOR
REVIEW AND APPROVAL.
.
ALL ITEMS OF SUPPLY SHALL BE MARKED IAW
MIL-STD-129.  IN ADDITION, EACH UNIT PACK WILL
BE MARKED WITH LOT AND SERIAL NUMBER (IF AVAILABLE),
CONTRACTOR'S CAGE CODE, ACTUAL MANUFACTURER'S
CAGE CODE AND PART NUMBER.

PCO MANDATORY INSPECTION. DURING PRODUCTION,
MANDATORY INSPECTION IS REQUIRED TO BE
ACCOMPLISHED AND DOCUMENTED BY THE CONTRACTOR AS
FOLLOWS:
.
CRITICAL AND MAJOR CHARACTERISTICS AS IDENTIFIED
IN CLASSIFICATION OF CHARACTERISTICS BLOCK ON
DRAWING(S), TECHNICAL SPECIFICATIONS, SECOND
TIER DOCUMENTS REFERENCED IN THE ACQUISITION
ITEM DESCRIPTION AND SPECIFIED IN THE
PROCUREMENT DOCUMENT, AND CHARACTERISTICS
DEFINED AS:
(A) MATERIAL CERTIFICATIONS
(B) DESTRUCTIVE AND / OR NONDESTRUCTIVE
TEST RESULTS (WHEN APPLICABLE)
(C) ATTRIBUTES FOR PLATING HARDNESS
.
IMPORTANT MINOR CHARACTERISTICS SHALL BE
DEFINED BY THE CONTRACTOR SUBJECT TO QAR
CONCURRENCE, UNLESS OTHERWISE DEFINED ON
APPLICABLE DRAWING(S), SPECIFICATIONS
AND CHARRACTERISTICS DEFINED AS:
(A) DIAMETRICAL AND LINEAR DIMENSIONS
HAVING A TOLERANCE OF +/- 0.005 INCH OR
LESS
(B) GEOMETRIC FEATURE CONTROLS HAVING A TOTAL
TOLERANCE OF 0.003 INCH OR LESS
(C) SURFACE FINISHES HAVING A 16 VALUE OR LESS
(D) CLASS THREE THREADS
(E) ANGULAR TOLERANCES WITH A TOTAL RANGE LESS
THAN 1 DEGREE
.
LEVEL OF INSPECTION: ANSI / ASQC Z1.4 FOR SINGLE
SAMPLING USING A GENERAL INSPECTION LEVEL O II
(A) CRITICAL AND MAJOR CHARACTERISTICS: 100%
INSPECTION APPLIES
(B) IMPORTANT MINOR CHARACTERISTICS: AQL OF 1.5
.
CERTIFICATION / DATA REPORTS: THE CONTRACTOR IS
RESPONSIBLE FOR PREPARING A CERTIFICATE OF
QUALITY COMPLIANCE (COQC) IN ACCORDANCE WITH THE
DD FORM 1423 CONTRACT DATA REQUIREMENTS LIST
(CDRL). THE COQC CONTENT WILL INCLUDE AS A
MINIMUM THE DATA DESCRIBED IN DLAR CLAUSE
52.246-9000, IN ADDITION TO ALL PCO MANDATORY
INSPECTION RESULTS. THIS COQC REQUIREMENT
APPLIES TO EACH UNIT OF CONTRACT QUANTITY.

CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE
USED NOR INCORPORATED IN ANY ITEMS TO BE
DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION
SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT
DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.
SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR
APPROVAL UNLESS THEY ARE AUTHORIZED BY THE
SPECIFICATION REQUIREMENTS.

52.246-11 Higher Level Contract Quality Requirement (Manufacturers)

FAR CLAUSE 52.246-11 APPLIES.  A QUALITY MANAGEMENT PROGRAM MEETING THE
REQUIREMENTS OF ISO 9001:2008; A PROGRAM COMPARABLE TO ISO 9001:2008
(EXAMPLE SAE AS 9100), THE FOLLOWING TAILORED VERSION OF ISO 9001:2008;
OR A PROGRAM COMPARABLE TO THE TAILORED VERSION OF ISO 9001:2008
(EXAMPLE SAE AS 9003) IS REQUIRED.   IN THE TAILORED VERSION OF THE ISO
9001:2008, ANY REFERENCES WHICH CITE THE ENTIRE INTERNATIONAL STANDARD
ARE INTERPRETED AS EXCLUSIONS TO THIS DOCUMENT.
DLA TAILORED HIGHER LEVEL QUALITY CLAUSE FROM ISO 9001:2008

4.1 General requirements, [excluding reference to 1.2 and excluding NOTE
3 c)]
4.2.1 General, [excluding subparagraph a)]
4.2.2 Quality manual, [excluding subparagraph a)]
4.2.3 Control of documents
4.2.4 Control of records
5.1 Management commitment
5.3 Quality policy
6.2.2 Competence, training and awareness
6.4 Work environment
7.1 Planning of product realization, [excluding NOTE 2]
7.2.1 Determination of requirements related to the product
7.2.2 Review of requirements related to the product
7.2.3 Customer communication
7.3.7 Control of design and development changes
7.4.1 Purchasing process
7.4.3 Verification of purchased product
7.5.1 Control of production and service provision
7.5.3 Identification and traceability
7.5.4 Customer property
7.5.5 Preservation of product
7.6 Control of monitoring and measuring equipment
8.1 General, [excluding subparagraph b) and subparagraph c)]
8.2.2 Internal audit
8.2.4 Monitoring and measurement of product
8.3 Control of nonconforming product
8.5.2 Corrective action
8.5.3 Preventive action

REMINDER: THIS IS A CRITICAL ITEM AND ALL
MAJOR AND MINOR WAIVER/DEVIATION REQUESTS MUST
BE FORWARDED TO THE DSCC CONTRACTING OFFICER WHO
WILL COORDINATE THE REVIEW AND APPROVAL THROUGH
THE RESPONSIBLE ENGINEERING SERVICE ACTIVITY.

NOTE: THIS IS A RESTRICTED SOURCE ITEM AND
REQUIRES ENGINEERING SOURCE APPROVAL BY THE
GOVERNMENT DESIGN CONTROL ACTIVITY.

"CERTIFICATE OF QUALITY COMPLIANCE IS MANDATORY"

THIS MATERIAL MUST MEET NAVAIR AIRCRAFT LAUNCH &
RECOVERY EQUIPMENT TRACEABILITY REQUIREMENTS. BARE
ITEM MARKINGS SHALL BE IAW THE TECHNICAL DATA
DRAWINGS PROVIDED.

BARE ITEM MATERIAL SHALL BE MARKED WITH CONTRACT
NUMBER, NAWC CAGE, AND PART NUMBER UNLESS OTHERWISE
SPECIFICIED ON ASSOCIATED DRAWING. IF A CONFLICT
EXISTS WITH MARKING REQUIREMENTS OF THIS 82N ALRE/SE
ITEM, THE ASSOCIATED DRAWING REQUIREMENTS SHALL APPLY.

EACH UNIT PACKAGE WILL BE MARKED WITH THE NSN,
CONTRACT NUMBER, LOT NUMBER, CONTRACTOR CAGE
CODE, MANUFACTURER CAGE CODE, AND PART NUMBER.

CAPY MACHINE SHOP INC. DBA 0BVP9 P/N 510445-1
MICRO STEEL INC. DBA 0T9A2 P/N 510445-1
AME INTERNATIONAL L.L.C. DBA 0W8V2 P/N 510445-1
HAWAIIAN HOST CANDIES OF L.A. INC. 0BR39 P/N 510445-1
WELLMAN DYNAMICS MACHINING AND 6JRD9 P/N 510445-1

IAW REFERENCE QAP 16236 SQAP009903783QA
REVISION NR     DTD 03/12/2014
PART PIECE NUMBER:

IAW REFERENCE QAP 16236 SQAP009903783
REVISION NR     DTD 03/12/2014
PART PIECE NUMBER:

IAW REFERENCE QAP 16236 CDRL-14-12025FAT
REVISION NR     DTD 01/27/2014
PART PIECE NUMBER:

IAW REFERENCE QAP 16236 CDRL-14-12025PTI
REVISION NR     DTD 01/27/2014
PART PIECE NUMBER:

IAW REFERENCE QAP 16236 CDRL-14-12025COQC
REVISION NR     DTD 01/27/2014
PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 16236 CN009903783
REVISION NR     DTD 03/12/2014
PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 80020 510445
REVISION NR G   DTD 02/22/2012
PART PIECE NUMBER: 510445-1

IAW REFERENCE DRAWING NR 80020 510465
REVISION NR J   DTD 09/16/2010
PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 80020 510466
REVISION NR D   DTD 06/28/2010
PART PIECE NUMBER: