ITEM DESCRIPTION FOR PR: 0043355457

  ADAPTER ASSEMBLY,RECOIL
  THIS ITEM IS A #DEFENSE ARTICLE# AS DEFINED IN AND
  SUBJECT TO THE INTERNATIONAL TRAFFIC IN ARMS
  REGULATIONS (22 C.F.R. 120#30) AND THE ARMS
  EXPORT
  CONTROL ACT (22 U.S.C.A. 2778#2799). ANY
  MANUFACTURER OR EXPORTER OF DEFENSE ARTICLES IS
  REQUIRED TO REGISTER WITH THE DIRECTORATE OF
  DEFENSE
  TRADE CONTROLS (DDTC), DEPARTMENT OF STATE.
  DOCUMENTARY EVIDENCE OF REGISTRATION MAY BE
  REQUIRED
  PRIOR TO AWARD. ADDITIONAL EXPORT RESTRICTIONS
  APPLY
  AS INDICATED HEREIN. FAILURE TO SUBMIT DDTC
  REGISTRATION WHEN REQUESTED WILL MAKE A
  QUOTE/OFFER
  INELIGIBLE FOR AWARD.
  ________________EXCEPTION DATA___________________
  MIL-DTL-16232, para 6.2.1- DD FORM 1423 is
  replaced
  by SUPPLEMENTAL QUALITY ASSURANCE PROVISION (SQAP)
  PHOS-DL-MANG
  IF DRAWING NOTE GIVES OPTION FOR ZINC OR MANGANESE
  COATING THEN MANGANESE IS REQUIRED.
  ______________END OF EXCEPTIONS__________________
  THE ITEM BEING PROCURED IS A CRITICAL GUN PART
  ITEM
  WITH UNIQUE REQUIREMENTS.
  PROCESS PROCEDURES AND OR WORKMANSHIP SPECIMENS
  REQUIRED BY MILITARY SPECIFICATION (S) APPLICABLE
  TO
  THIS CONTRACT WILL BE APPROVED BY THE CONTRACT
  POST
  AWARD CONTRACTING OFFICER (PCO). POST AWARD
  PREPRODUCTION APPROVAL VERIFYING THE REQUIREMENTS
  OF MIL-DTL-16232 IS
  REQUIRED.
  A CONTRACT DATA REQUIREMENTS LIST (CDRL),
  IDENTIFIED
  IN A SQAP AS A PHOS-DL-MANG AND A SUGGESTED
  OUTLINE,
  IDENTIFIED IN A SQAP AS PHOS-OUTLINE-16232,
  PROVIDE
  THE PHOSPHATE COATING PROCEDURE
  REQUIREMENTS/FORMAT
  AND ARE INCLUDED IN THE TECHNICAL DATA PACKAGE.
  THE CONTRACTOR MUST PROVIDE COPIES OF PHOSPHATE
  COATING PROCEDURES WRITTEN SPECIFICALLY FOR THE
  COATING OF PARTS ON THIS CONTRACT TO THE PCO
  WITHIN
  45 DAY AFTER AWARD. AN ADDITIONAL 30 DAYS WILL BE
  REQUIRED FOR REVIEW/APPROVAL DETERMINATION.
  PRODUCT INSPECTION WILL BE CONDUCTED BY THE DCMA
  QAR AT THE ACTUAL MANUFACTURER'S FACILITY AND IN
  PROCESS INSPECTIONS WILL OCCUR AT THE PHOSPHATE
  CONTRACTOR'S FACILITY IDENTIFIED ON THIS CONTRACT.
  THE IDENTIFICATION OF THE ACTUAL MANUFACTURER AND
  PHOSPHATE CONTRACTOR MUST BE SUBMITTED TO THE
  CONTRACTING OFFICER FOR INCLUSION IN THE AWARD.
  UPON AWARD, ANY CHANGES TO THE ABOVE MUST BE
  APPROVED BY THE PCO VIA FORMAL CONTRACT
  MODIFICATION.
  A WAIVER FOR THE PHOSPHATE PREPRODUCTION
  REQUIREMENTS OF MIL-DTL-16232 PARAGRAPH 3.1 CAN BE
  SUBMITTED. THE DOCUMENTATION REQUIRED FOR
  EVALUATION OF THIS WAIVER REQUEST MUST INCLUDE: A
  PHOSPHATE PROCEDURE THAT HAS BEEN REVIEWED AND
  APPROVED BY THIS PROCURING AGENCY AND A TEST
  REPORT
  (GOVERNMENT FIRST ARTICLE OR PRODUCTION
  VERIFICATION
  TEST)FROM WITHIN THE LAST YEAR IN WHICH THE
  PHOSPHATE
  COATING WAS TESTED AND PASSED(FOR ANY NSN).
  THIS NSN CONTAINS ONE OR MORE COMPONENTS WHICH
  MUST
  MEET QPL/QML SPECIFICATIONS AS IDENTIFIED IN THE
  TECHNICAL DATA PACKAGE. CLAUSE I09A01 (FAR CLAUSE
  52.209-1) QUALIFICATION REQUIREMENTS IS
  APPLICABLE.
  THE AWARDEE SHALL PROVIDE QPL/QML COMPONENTS ONLY
  FROM SOURCES QUALIFIED ON THE APPLICABLE QPL(S)/
  QML(S). THE IDENTIFICATION OF ALL APPLICABLE QPL/
  QML SOURCES MUST BE SUBMITTED TO THE CONTRACTING
  OFFICER FOR EVALUATION PRIOR TO CONTRACT AWARD.
  PRODUCT VERIFICATION TESTING (PVT) CLAUSE DLAD
  52.246-9004 MAY BE INVOKED FOR THE REFERENCED
  CONTRACT. IF INVOKED, PVT SAMPLES MUST BE
  INSPECTED,
  PACKAGED AND MARKED AS REQUIRED IN THE CONTRACT.
  ONE
  (1) SAMPLE MAY BE DESTROYED DURING TESTING.
  PRODUCT VERIFICATION TESTING, IF INVOKED, WILL BE
  PERFORMED PRIOR TO ACCEPTANCE OF EACH SHIPMENT.
  THE
  CONTRACTOR MUST PROVIDE PVT SAMPLES FROM EACH
  SUBCONTRACTOR AND FROM EACH PHOSPHATE CONTRACTOR
  USED
  IN THE PRODUCTION OF PARTS ON THIS CONTRACT. FIVE
  (5)
  PVT SAMPLES WILL BE REQUIRED TO BE IDENTIFIED TO
  THOSE SUBCONTRACTORS AND PHOSPHATE CONTRACTORS
  WHEN
  THEY ARE SENT IN FOR TESTING.
  CERTIFICATE OF CONFORMANCE IS NOT AUTHORIZED.
 
DLAD 52.246-9003, MEASURING AND TEST EQUIPMENT,
APPLIES.
 
THE INTERNATIONAL ORGANIZATION FOR
STANDARDIZATION (ISO) 9002 OR A "TAILORED"
PROGRAM MEETING THE FOLLOWING ISO 9002
PARAGRAPHS APPLIES:
4.5, DOCUMENT CONTROL: LIMITED TO INSPECTION
AND TESTING AS WELL AS APPLICABLE DRAWINGS,
SPECIFICATIONS AND INSTRUCTIONS REQUIRED BY
CONTRACT
4.6, PURCHASING: 4.6.1 AND LIMITED TO 4.6.2 A)
AND 4.6.4.2, ALL OTHER PARTS OF PARAGRAPH
ARE HEREBY DELETED
4.7, CUSTOMER-SUPPLIED PRODUCT:
4.8, PRODUCT IDENTIFICATION & TRACEABILITY:
4.10, INSPECTION & TESTING:
4.11, INSPECTION, MEASURING & TEST EQUIPMENT:
4.12, INSPECTION AND TEST STATUS:
4.13, CONTROL OF NONCONFORMING PRODUCT:
4.14, CORRECTIVE AND PREVENTIVE ACTION:
PARAGRAPH 4.14.3 APPLY TO PRODUCT ONLY
4.16, QUALITY RECORDS:
FAR CLAUSE 52.246-11 APPLIES
 
THIS ITEM HAS TECHNICAL DATA THAT IS SUBJECT TO
EXPORT CONTROL REGULATIONS, OR THE ITEM HAS NO
TECHNICAL DATA BUT IT IS LISTED ON THE UNITED
STATES MUNITIONS LIST (USML) OR THE COMMERCE
CONTROL LIST (CCL), AND IT IS THEREFORE
CONTROLLED FOR EXPORT BY THE INTERNATIONAL
TRAFFIC IN ARMS REGULATION (ITAR) OR EXPORT
ADMINISTRATION REGULATION (EAR).  (SEE DFARS
CLAUSE 252.204-7008.)

DISTRIBUTION OF THE TECHNICAL DATA AND
ELIGIBILITY FOR AWARD ARE LIMITED TO THOSE
SUPPLIERS QUALIFIED THROUGH JCP CERTIFICATION,
OR TO THOSE LICENSED BY EITHER THE DEPARTMENTS
OF STATE OR COMMERCE; OR TO FOREIGN SUPPLIERS
PURSUANT TO INTERNATIONAL AGREEMENTS.

TO APPLY FOR JCP CERTIFICATION, COMPLETE DD FORM
2345, "MILITARY CRITICAL TECHNICAL DATA
AGREEMENT," FORM IS AVAILABLE AT THE WORLD WIDE
WEB ADDRESS:

HTTP://WWW.LOGISTICSINFORMATIONSERVICE.DLA.MIL/J
CP/,

OR BY WRITING TO:

UNITED STATES/CANADA JOINT CERTIFICATION OFFICE
DLA LOGISTICS INFORMATION SERVICE
FEDERAL CENTER
74 WASHINGTON AVE., NORTH
BATTLE CREEK, MI 49017-3084

TO MANUFACTURE THIS ITEM, NON-JCP CERTIFIED
SUPPLIERS MUST SUBMIT A CURRENT MANUFACTURING
LICENSE AGREEMENT, TECHNICAL ASSISTANCE
AGREEMENT, DISTRIBUTION AGREEMENT OR OFF-SHORE
PROCUREMENT AGREEMENT APPROVED BY THE
DIRECTORATE OF DEFENSE TRADE CONTROLS WITH THE
OFFER, UNLESS AN EXEMPTION UNDER THE PROVISIONS
OF ITAR SECTION, 125.4 "EXEMPTIONS OF GENERAL
APPLICABILITY," AND/OR EAR PART 740 ARE
APPLICABLE.

NON-JCP CERTIFIED SUPPLIERS SEEKING EXPORT
CONTROLLED TECHNICAL DATA ARE REQUIRED TO
PROVIDE THE CONTRACTING OFFICER WITH AN
APPLICABLE AGREEMENT OR IDENTIFY WHICH ITAR/EAR
EXEMPTION APPLIES TO RECEIVE A COPY OF THE
EXPORT CONTROLLED TECHNICAL DATA.

NOTE:  SUPPLIERS ARE REQUIRED TO IDENTIFY
SUB-CONTRACTORS AT TIME OF QUOTING IF KNOWN.
USE OF ANY SUB-CONTRACTOR SUPPLIER WILL REQUIRE
JCP CERTIFICATION APPROVAL.

 
THIS NSN CONTAINS ONE OR MORE COMPONENTS WHICH
MUST MEET QPL/QML SPECIFICATIONS.BY SUBMITTING
AN OFFER, THE OFFEROR AGREES TO PROVIDE QPL/QML
COMPONENTS ONLY FROM SOURCES QUALIFIED ON THE
APPLICABLE QPL(S)/QML(S).
 
CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE
USED NOR INCORPORATED IN ANY ITEMS TO BE
DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION
SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT
DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.
SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR
APPROVAL UNLESS THEY ARE AUTHORIZED BY THE
SPECIFICATION REQUIREMENTS.
I/A/W   QAP    16236 PHOS-DL-MANG
REFNO
AMEND NR      DTD 11/05/10
TYPE NUMBER

I/A/W   QAP    16236 PHOS-OUTLINE-16232
REFNO
AMEND NR A     DTD 10/15/10
TYPE NUMBER

I/A/W   QAP    16236 PHOS-QAR-CHECK
REFNO
AMEND NR A     DTD 10/15/10
TYPE NUMBER

I/A/W   DRAWING NR 19200 11686866
REFNO
AMEND NR D     DTD 04/06/67
TYPE NUMBER

I/A/W   DRAWING NR 19200 7268307
REFNO
AMEND NR G     DTD 11/08/56
TYPE NUMBER

I/A/W   DRAWING NR 19200 7269485
REFNO
AMEND NR J     DTD 09/12/96
TYPE NUMBER

I/A/W   DRAWING NR 19200 8447734
REFNO
AMEND NR C     DTD 09/17/96
TYPE NUMBER

I/A/W   DRAWING NR 19204 11838567
REFNO
AMEND NR B     DTD 07/06/76
TYPE NUMBER

I/A/W   DRAWING NR 19204 8437670
REFNO
AMEND NR F     DTD 11/15/02
TYPE NUMBER

I/A/W   DRAWING NR 30003 537AS185
REFNO
AMEND NR C     DTD 12/30/94
TYPE NUMBER

I/A/W   DRAWING NR 30003 537AS265
REFNO
AMEND NR B     DTD 01/01/39
TYPE NUMBER

I/A/W   DRAWING NR 30003 537AS269
REFNO
AMEND NR      DTD 07/23/74
TYPE NUMBER

I/A/W   DRAWING NR 30003 537AS269
REFNO
AMEND NR      DTD 07/23/74
TYPE NUMBER

I/A/W   DRAWING NR 30003 537AS270
REFNO
AMEND NR      DTD 07/22/74
TYPE NUMBER

I/A/W   DRAWING NR 30003 537AS271
REFNO
AMEND NR      DTD 07/22/74
TYPE NUMBER

I/A/W   DRAWING NR 30003 537AS272
REFNO
AMEND NR      DTD 07/22/74
TYPE NUMBER

I/A/W   DRAWING NR 30003 537AS273
REFNO
AMEND NR B     DTD 02/01/78
TYPE NUMBER

I/A/W   DRAWING NR 30003 537AS283
REFNO
AMEND NR B     DTD 02/01/78
TYPE NUMBER

I/A/W   DRAWING NR 30003 537AS284
REFNO
AMEND NR A     DTD 10/28/73
TYPE NUMBER

I/A/W   DRAWING NR 30003 537AS285
REFNO
AMEND NR A     DTD 10/01/75
TYPE NUMBER

I/A/W   DRAWING NR 30003 537AS287
REFNO
AMEND NR A     DTD 12/16/75
TYPE NUMBER

I/A/W   DRAWING NR 30003 537AS300
REFNO
AMEND NR A     DTD 10/03/75
TYPE NUMBER

I/A/W   DRAWING NR 30003 537AS300
REFNO
AMEND NR C     DTD 09/25/78
TYPE NUMBER

I/A/W   DRAWING NR 30003 537AS300
BASIC
AMEND NR B     DTD 02/09/77
TYPE NUMBER

I/A/W   DRAWING NR 30003 537AS534
REFNO
AMEND NR      DTD 07/22/74
TYPE NUMBER

I/A/W   SPEC NR MIL-DTL-16232G
REFNO
AMEND NR G
TYPE NUMBER

I/A/W   SPEC NR MIL-PRF-16173E(I1)
REFNO
AMEND NR 1
TYPE NUMBER

I/A/W   SPEC NR MIL-PRF-3150E
REFNO
AMEND NR 2
TYPE NUMBER

I/A/W   SPEC NR QPL-16173-84 NOT 1
REFNO
AMEND NR 84
TYPE NUMBER

I/A/W   SPEC NR QPL-3150-34 NOT 1
REFNO
AMEND NR 34
TYPE NUMBER